315/35 nitto's AND tailpipes...pics

BERT306 · Dec 4, 2005

Alot of people wonder if 315's fit on a fox: YES they do. I didn't think my tailpipes would fit but, YES they do:

and some random pics before tailpipes:

Look Its Aaron · Dec 4, 2005

Please give some more description of your set up. What axles did you use etc...

timewarped1972 · Dec 4, 2005

that is just a sweet lookin car!

BERT306 · Dec 4, 2005

Look Its Aaron said:
Please give some more description of your set up. What axles did you use etc...

Stock length ranger axles, no quads or spacers. I had to do some clearancing on the inner fender w/a BFH. Did not roll the outer lip at all.

Up front i used 5/16" spacers w/lincoln rotors and a 245/45 tire.
:SNSign:

dirty slut · Dec 4, 2005

that car is absolulty beautiful, nice work!!

TrophyHead · Dec 4, 2005

That is bad ass man.

What size/brand cat-back are you using? Also what kind of rear springs?

PRO50SC · Dec 4, 2005

what size wheel?

5spd GT · Dec 4, 2005

Looks like 03 17x10.5's out back and 17x9's in the front...looks good

Look Its Aaron · Dec 4, 2005

can you get any shots the rear?

old_blue · Dec 4, 2005

rear wheel size please.......

BERT306 · Dec 4, 2005

17X9's front AND back. The nitto's run small so i don't think i'd get a BFG drag radial on there.
Flowmaster Cat-back, and hacked-up factory springs (I immediately regreted that decision BTW) Lookin to get some Eibach pro's and some strange adjustable struts/shocks.
Thanks for the comments!:Word:

BERT306 · Dec 4, 2005

Here's the only rear pics i have other than the one i already put up:

And before tails and hackin o the springs:

BERT306 · Dec 4, 2005

Here is a short walk around vid i made awhile back--> http://videos.streetfire.net/Player.aspx?fileid=DE101D14-EF46-47A7-A737-CDD25A543688
Here's the mod's:
stock short block bored .030
Windsor Jr. iron heads
Crane 1.6 rockers
X-303 cam
24# inj.
Eddy perf. rpm & 1" spacer
BBK 70mm TB & EGR
C&L 76mm MAF
MSD 6AL ign.
MSD coil
Lontubes, h-pipe, 2 chamb Flows
NOS 125hp dry shot (unused now)
V-1 S-trim @10lbs w/ 10 rib
AFM power pipes
Mondo Bypass valve
Spec Stg 3 clutch
alum driveshaft
3.73 gears
South side upper + lower control arms
5 lug conv. (ranger axles, lincoln rotors)
Weld in Subframe conn.
6 pt cage
Jeg's sport seats
I think thats all? I should have just updated my sig instead

86bluecobra · Dec 4, 2005

i want to know what it will do in the 1/4 now.

91ghp5.0 · Dec 4, 2005

any pics of the seats? man that fox is ****in beautiful.

BERT306 · Dec 4, 2005

86bluecobra said:
i want to know what it will do in the 1/4 now.

I want to know too track is an hour and a half away:damnit:
I'll get there someday...

And the seats:

tunedin302 · Dec 4, 2005

Sweet

Look Its Aaron · Dec 4, 2005

hmm, I may be wrong but I dont think that roll cage will pass tech. The bars look to be way too low.

BERT306 · Dec 4, 2005

Look Its Aaron said:
hmm, I may be wrong but I dont think that roll cage will pass tech. The bars look to be way too low.

I don't think it's fast enough to require a cage anyway. It was in there when i bought it. Any higher and i would have cut them out already.

5spd GT · Dec 4, 2005

What modifications needed to be done to the car's seat brackets to get those seats in there?

315/35 nitto's AND tailpipes...pics

Member

Attachments

Your car looks like it came straight from Mexico.

Member

Member

New Member

New Member

"the 5.0 owns all"

Your car looks like it came straight from Mexico.

Member

Member

Attachments

Member

Advanced Member

Active Member

Member

Attachments

I AM the law!!!

Your car looks like it came straight from Mexico.

Member

"the 5.0 owns all"

Similar threads

Privacy & Transparency

Privacy & Transparency