• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

351Windsor heads VS E7TE heads

  • Thread starter Thread starter stevesLX
  • Start date Start date Aug 8, 2007

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Aug 8, 2007
#1
  • Aug 8, 2007
  • #1
O.K. guys I currently have E7TE heads on my motor right now that have a 3 angle valve job and have been ported. I have the opprotunity to pick up a set of 351W DOOE heads from a guy for 50.00. He says they are eith 1969 or 1970. He is not sure and he thinks they are stock. So with that info is this going to be an improvement over my E7's or not? And is there anything I should pay attention too when I look at these other ones. I am new to this.
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Aug 8, 2007
#2
  • Aug 8, 2007
  • #2
That's a hard call to make, honestly. They may not offer any improvement over your ported E7's if they're stock, but they probably do have more potential if you plan on doing some port work to them. If I recall correctly, they are one of the better factory castings, but you may end up putting enough money into them with machine work that a set of aftermarket heads start looking more attractive for the money spent, IMO.
 

85_SS_302_Coupe

it sucks (I know) to be on the receiving end
15 Year Member
Nov 11, 2003
6,945
1,598
223
Northern KY
Aug 8, 2007
#3
  • Aug 8, 2007
  • #3
Stock for stock the 351 heads have bigger valves and breath much freer than E7s (if we're talking about the D0 series heads). They should have 1.84/1.54 valves compared to the E7's 1.78/1.45 valves. The down side is i believe they have a slightly larger combustion chamber so you might lose a little compression, but not a lot. If you take them to a shop to have them cleaned up you can have them milled down some to boost compression on them.

I have a set of C90E's which are the '69 heads, these are the ones everyone looks for when you mentioned old 351 heads. I got them with some pretty extensive port work and 1.94/1.60 valves but a few valves were bent. I took them to a local shop to get new valves done and the guy there said he hadn't seen port work that good in a long time since a lot of people just do CNC porting now.

Either way for $50 i'd say they're worth a shot....the only thing you have to keep in mind is if they're '69-70 heads, they're going to need valve guides for sure because back then they used leaded gas to lubricate the valves....you'll need to use newer style guides since you're not running leaded. If you're going to do that you might wanna just go ahead and get a valve job done while you've got the valves out, so you might expect to put a few hundred into them...so that's your call.
 

Modular2v

Founding Member
Jun 30, 2002
3,222
23
99
oklahoma
Aug 8, 2007
#4
  • Aug 8, 2007
  • #4
my 331 went 12.06@114 with a set of c9 heads
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
Aug 8, 2007
#5
  • Aug 8, 2007
  • #5
If they are c9'sthey are worth it for sure. They will flow much better then the E7's.
 

fastgtfairlane

New Member
Apr 7, 2006
266
0
0
Aug 8, 2007
#6
  • Aug 8, 2007
  • #6
i would get those heads
 
You must log in or register to reply here.

Similar threads

Place to Avoid: Jamison Auto Group in Gulfport, MS
  • D Durden
  • Oct 20, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • 2 3
Replies
46
Views
4K
1965 - 1973 Classic Mustangs -General/Talk- Jul 16, 2026
Noobz347
Which one of these 3 intakes make the most sense for my 331 combo
  • from6to8
  • Jul 25, 2024
  • 1994 - 1995 Specific Tech
Replies
7
Views
2K
1994 - 1995 Specific Tech Jul 26, 2024
AeroCoupe
Y
Dyno Comparison for TFS 44cc Ported Heads vs PI Ported Heads with same VT Stage 2 Cams
  • Yel2002GTAuto
  • Oct 13, 2022
  • SN95 4.6L Mustang Tech
Replies
15
Views
10K
SN95 4.6L Mustang Tech Jan 29, 2023
Yel2002GTAuto
Y
Engine Blue Print head swap
  • HemiRick
  • Sep 8, 2020
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
46
Views
10K
Fox 5.0 Mustang Tech Jun 12, 2022
Potomus Pete
There is just something about a Foxbody
  • thatblackfoxbody
  • Feb 18, 2022
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 20, 2022
90sickfox
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?