Progress Thread 43 years later

2Blue2 · Jun 19, 2020

Enzio said:
Not too difficult.

He had two specialty tools and an arbor press.
Soooooo. not happening in the drive way today.

But I found one fitting that needed snugging so maybe leak will slow down to a seep.

Enzio said:
I've given up on the billet pulleys. Can't find anything even close.

Spray Paint!! For the Win!!

Enzio · Jun 20, 2020

I've been wire brushing like a madman all day. Still much better than the motor mounts.
Time for a beer.

IICrew · Jun 20, 2020

Look into electrolysis. Cuts the brush time dramatically. I only brush large flakes of rust on items that fit in my tote. I've gotten so lazy I don't even degrease parts first. I will wipe down heavy oil or grease otherwise the vat takes it off. My pulleys came out looking like new bare steel.
I just pressure wash items. Soak for 24 hours or so in the vat. Heavy rust takes longer. Degrease then pressure wash. Let dry thoroughly and treat with a coat of coroseal. Gets rust in the nooks and crannies. Not perfect for everything but ease of use is phenomenal.

Enzio · Jun 21, 2020

Duh! I didn't even think of it. What the heck? I'm almost done though. Just a few accessory brackets left.

2Blue2 · Jun 21, 2020

View: https://youtu.be/wwpXUn2dF5c

Attention Agent E
Your mission should you accept is to obtain secret images of the Mutt2 in body work...
Remember we will disavow all knowledge of this excursion.
This message will set destruct in 5, 4, 3, 2, 1,..................

Enzio · Jun 21, 2020

I'll work on that.

Enzio · Jun 24, 2020

Got these back today.

2Blue2 · Jun 24, 2020

Them s as pretty as hot apple pie

LILCBRA · Jun 24, 2020

Enzio said:
Got these back today.

That's what my headers looked like about 20 years ago....

Enzio · Jul 1, 2020

Machine work is completed on the engine. They are starting assembly late this week.
Body is being stripped. For some reason I got bumped by a Camaro....

LILCBRA · Jul 1, 2020

Must be Chevy lovers who run the shop.

Enzio · Jul 7, 2020

So 2Blue2 got me thinking about a hydraulic clutch. I think a Tilton 6000 series would be really simple to install on the slave portion. It's the master cylinder that's a problem. I asked the guys at Classic Auto Reproductions and they do not know of anyone who's done it. If I could figure it out I'd go with it. With the difference in height of the Spec Clutch from Original, I don't like the angle of the clutch fork and the TOB. It worked but the clutch cable is out so far there is barely enough adjustment and if I can't figure out how to get a master cylinder installed then I'll keep it.

2Blue2 · Jul 7, 2020

Would have to make an adaptor plate?

Enzio · Jul 7, 2020

I've been looking at that. I still don't know if there is room under the brake booster...because I can't...
And the adapter plate would be where? The clutch lever pivots similar to what is shown only the clutch cable attaches above the pivot point instead of below as shown. On yours is there room under the booster?

2Blue2 · Jul 7, 2020

Enzio said:
And the adapter plate would be where?

Right where the clutch tube bolts on to hold master and to distance it out a bit.
That pedal bracket lever would go upside down to get pedal arm in right spot.
Would have to weld ears to it and drill a hole in clutch pedal rod? Modify push rod ect...

Sorry just spit ball engineering.

The above picture's approach would work but all would have to be modified to fit our Mutt2s
Just got to throw that master cylinder in there and and pack all around it with hundred dollar bills, THEN IT WILL WORK!

Enzio · Jul 7, 2020

MDL is sending me something they think may work.

extra_stout · Jul 7, 2020

I have just a rod with a ball joint bolted to the clutch pedal (no levers). My master and slave have the same diameter, so I have a similar distance from pivot to cable attachment. You can have a look to my build thread there are some pictures with the master clutch cylinder beside the brake cylinder (without booster)...

2Blue2 · Jul 7, 2020

Can kind of see it in Extra_Stout's picture
Look at all that new / clean / painted stuff...

This pic shows it better

well almost, at least I "feel" better .

Enzio · Jul 7, 2020

I looked. I'm thinking that for me with the stock bell a slave inside the bell mounted on the transmission shaft would be a better fix. Yours looks real nice. I like the solid line from master to slave. How does that react to the engine torque?

This is what MDL sent me:

Enzio · Jul 7, 2020

I'm getting thirsty.
Isn't there a steel plate under the dash to hold the steering shaft up? I wonder if a guy could fab a plate to hold the master there and then run the lines through a grommet where the cable was?

Progress Thread 43 years later

will be trying this sex one when I can find it

Dang it. I was hoping mine would get 3 more inches

Attachments

Mustang Master

Dang it. I was hoping mine would get 3 more inches

will be trying this sex one when I can find it

Dang it. I was hoping mine would get 3 more inches

Dang it. I was hoping mine would get 3 more inches

Attachments

will be trying this sex one when I can find it

I wish I didn't have all of these balls in the air

Dang it. I was hoping mine would get 3 more inches

I wish I didn't have all of these balls in the air

Dang it. I was hoping mine would get 3 more inches

will be trying this sex one when I can find it

Dang it. I was hoping mine would get 3 more inches

will be trying this sex one when I can find it

Dang it. I was hoping mine would get 3 more inches

will be trying this sex one when I can find it

Dang it. I was hoping mine would get 3 more inches

Dang it. I was hoping mine would get 3 more inches

Similar threads

Privacy & Transparency

Privacy & Transparency