• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Best plugs for carb'd roller

  • Thread starter Thread starter forango
  • Start date Start date Nov 21, 2025
Prev
  • 1
  • 2
  • 3
First Prev 3 of 3
F

forango

Active Member
Feb 19, 2003
148
17
28
south florida
Nov 25, 2025
#41
  • Nov 25, 2025
  • #41
rednotch said:
Its a carb car, bit different for initial vs the efi stuff, what's it seeing full advanced, are you checking it with a decent dial back light or just setting initial, good way to see if the marks are off with a dial back light. How are you controlling the timing, threw the msd box or a vacuum advance or are you just running it locked with a stock type tfi distributor? Popping and farting on decel, make sure its got 0 exhaust leaks first, then Check rest of the ignition components. Backfire like bang, like can take out a muffler bang, definitely want to look at the carb too, might need a rebuild kit or rejet. A sub $100 wideband gauge with a good bosch sensor is a good investment.

Timing mark getting pretty close to the base of the strap. If your reading plugs for everything shut it off, pull over, swap a few of the old ones in and drive it back. Corners plugs if you don't want to do them all.
Click to expand...
I have yet to check the total adevance because I haven't had a second person to assist with controlling the throttle. I am going to try and work that this weekend since I will have someone to help

The distributor is the steel gear verson for an '85 GT...The carb is practically new but it did sit for a while during the engine swap but still technically only a year old...Definitely an exhaust leak or two I am constantly chasing but nothing major
 
F

forango

Active Member
Feb 19, 2003
148
17
28
south florida
Nov 25, 2025
#42
  • Nov 25, 2025
  • #42
General karthief said:
Or a bad balancer.
I'd deal with the timing, check balancer, make sure 0* on the balancer is TDC on the #1 piston, rotor at #1 on cap..
Click to expand...
The TDC, rotor and balancer shoudl all be good...I had to redo the distributor a few times to get it right but i will try asnd recheck it
 
F

forango

Active Member
Feb 19, 2003
148
17
28
south florida
Nov 25, 2025
#43
  • Nov 25, 2025
  • #43
AeroCoupe said:
Base timing on most 302’s is around 12 to 14 degrees. You sure you don’t have the distributor off a tooth or a worn out timing chain? I just throwing stuff out but that seems to be a lot of initial timing to me.
Click to expand...
I am not "sure" of anything. LOL...I bought the engine already built but unless the builder screwed up the timing chain shoudl be solid..the engine only has about 10K total miles on it
 
F

forango

Active Member
Feb 19, 2003
148
17
28
south florida
Nov 25, 2025
#44
  • Nov 25, 2025
  • #44
I appreciate all the replies and info btw...Seems to be something I will be chasing for a while and potentailly never get just right...The bitch is when this thing is in the powerband at WOT it screams and moves out
 

Noobz347

Stangnet Facilities Maint Tech... Er... Janitor
Admin Dude
Jan 4, 1985
43,062
21,226
234
Box behind Walmart
Nov 25, 2025
#45
  • Nov 25, 2025
  • #45
I have two sneaking suspicions to add to what the dudes have said above:



Lean pop - The white residue on your plugs indicates [lean] to me. This can cause a pop on deceleration.



I would also suggest that a leaking injector can cause this too but you're carb'd so, fuel may be working it's way into the engine when fuel is supposed to be [closed] off.
 
R

Rcdgl

5 Year Member
Feb 19, 2018
313
168
63
Nov 25, 2025
#46
  • Nov 25, 2025
  • #46
autolite or motorcraft plugs, gap for stock spec and try that.
 
F

forango

Active Member
Feb 19, 2003
148
17
28
south florida
Nov 25, 2025
#47
  • Nov 25, 2025
  • #47
I think I figured out an area where I can do a nice WOT hit and immediately shut it down and pull off to check the plugs....Here is my question:

Is it ok to pull a couple plugs while the engine is that hot or am I risking damaging the threads in the heads?
 

AeroCoupe

lube between the nut and the face. I know my lubes
Founding Member
Oct 28, 2001
5,870
3,994
183
Claremore, OK
Nov 25, 2025
#48
  • Nov 25, 2025
  • #48
Very little risk and I only say that due to the odds are you will burn yourself.
 
Reactions: DadLife0724
F

forango

Active Member
Feb 19, 2003
148
17
28
south florida
Nov 25, 2025
#49
  • Nov 25, 2025
  • #49
AeroCoupe said:
Very little risk and I only say that due to the odds are you will burn yourself.
Click to expand...
I likely will find a way to do that. LOL
 
F

forango

Active Member
Feb 19, 2003
148
17
28
south florida
Dec 1, 2025
#50
  • Dec 1, 2025
  • #50
Ok so I found a spot to do a decent WOT pull from about 25--80ish...These are plugs 1 and 5
 

Attachments

  • AS1.webp
    34.4 KB · Views: 60
  • AS2.webp
    35.9 KB · Views: 61
  • AS3.webp
    34 KB · Views: 69
  • AS4.webp
    26.3 KB · Views: 67
  • AS5.webp
    44.2 KB · Views: 68
  • AS6.webp
    40.3 KB · Views: 70
  • AS7.webp
    56.6 KB · Views: 56
  • AS8.webp
    42.1 KB · Views: 65

FastDriver

I was uncomfortably high & wearing a helmet
SN Certified Technician
Sep 5, 2001
6,089
2,690
224
Vass, NC
Dec 1, 2025
#51
  • Dec 1, 2025
  • #51
AFR looks good to me. Couple plugs want a tad less timing... others are on point. I'd pull a degree, but I err conservative.
 
F

forango

Active Member
Feb 19, 2003
148
17
28
south florida
Dec 2, 2025
#52
  • Dec 2, 2025
  • #52
FastDriver said:
AFR looks good to me. Couple plugs want a tad less timing... others are on point. I'd pull a degree, but I err conservative.
Click to expand...
Technically these are only 2 plugs..the front corners...not sure which one looks perfect and which is a touch off
 

HotFox

15 Year Member
Jan 5, 2009
1,051
656
164
SE Michigan
Dec 2, 2025
#53
  • Dec 2, 2025
  • #53
Blue strap means to much timing! I would replace plugs (atleast the blued ones) and pull atleast 2 degrees, test again. A carb will be inherently rich, put cats on if you want it to smell better.
Tune for leanest cylinder...
 
Prev
  • 1
  • 2
  • 3
First Prev 3 of 3
You must log in or register to reply here.

Similar threads

6
Hey all,I’m putting together a 302 for my 1968 Mustang and wanted to post the combo + some questions to make sure I’m not missing crucial
  • 68_Disgustang
  • Feb 22, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
4
Views
854
1965 - 1973 Classic Mustangs -General/Talk- Jun 20, 2026
gray owl
G
SURGING IDLE / NO IDLE CHECKLIST FOR 1999–2004 MUSTANG GT (4.6L 2V) - Work In Progress
  • Noobz347
  • Aug 30, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
888
1996 - 2004 SN95 Mustang -General/Talk- Aug 30, 2025
Noobz347
Which one of these 3 intakes make the most sense for my 331 combo
  • from6to8
  • Jul 25, 2024
  • 1994 - 1995 Specific Tech
Replies
7
Views
2K
1994 - 1995 Specific Tech Jul 26, 2024
AeroCoupe
For Sale 94 Cobra 408w AOD Project For Sale
  • Labora
  • Oct 11, 2024
  • SN95 Mustangs For Sale (1994-04)
Replies
1
Views
1K
SN95 Mustangs For Sale (1994-04) Apr 7, 2025
Labora
M
Vacuum or Timing issue
  • Moistbois
  • Dec 20, 2021
  • Classic Mustang Specific Tech
Replies
3
Views
1K
Classic Mustang Specific Tech Feb 10, 2022
General karthief
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?