• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

brake booster

  • Thread starter Thread starter NFGTragedy
  • Start date Start date Jun 6, 2006
N

NFGTragedy

New Member
Oct 19, 2004
155
0
0
Rochester, NY
Jun 6, 2006
#1
  • Jun 6, 2006
  • #1
just curious if there is an easy way to swap it... i need to swap my 4cyl one for the v8 one i have in my garage... do i have to do it from the inside of the car and undo the 4 bolts... or can i do it all from the outside of the car some how. It looks like a bitch to work up under the steering wheel / dashboard. Any ideas?
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Jun 6, 2006
#2
  • Jun 6, 2006
  • #2
Nope... no matter how ya look at it, it's a pain in the arse. What's worse is that you have to elongate one of the holes to make it all fit right with some versions of the brake booster (the 94/95 for instance). If the motor is out of the car it makes things much easier but you still gotta dig up under that dash to get the nuts. Much easier if you pull the driver's seat and just lay down on the floor.

I feel your pain man... I have the same thing to do on my car. The last one I helped with wasn't too awful bad. We had two sets of hands, a case of beer, and all day to do it.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,376
18,123
224
Massachusetts
Jun 6, 2006
#3
  • Jun 6, 2006
  • #3
Only thing going for you is the V8 Fox booster is smaller than the SN95 boosters, so you might have an easier time wiggling it in.

You still gotta crawl under the dash and remove the 4 nuts and disconnect the brake pedal
 
N

NFGTragedy

New Member
Oct 19, 2004
155
0
0
Rochester, NY
Jun 6, 2006
#4
  • Jun 6, 2006
  • #4
ok... if thats the deal then how do i get the pedal to come off without messing up the wiring and stuff thats mounted at same bolt?
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Jun 6, 2006
#5
  • Jun 6, 2006
  • #5
For lack of step by step.... Veeeeeeeery carefully. That part wasn't all that difficult.. just make note of how it comes apart. The hard part is just holding your tungue just right in order to wiggle your ham fists up under that dash.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,376
18,123
224
Massachusetts
Jun 6, 2006
#6
  • Jun 6, 2006
  • #6
Take the driver's seat out...will make getting under there easier
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jun 6, 2006
#7
  • Jun 6, 2006
  • #7
Been there & done that…

Fox instructions for stock booster:

1.) Remove the 2 nuts holding the master cylinder to the booster. Pull back on the master cylinder until it clears the booster.. This works in some cases but not every time. If there is not sufficient clearance to remove the booster, you will have to bolt the master cylinder back down so that you can remove the brake lines.
2.) Open the driver’s door & slide the seat all the way back.
3.) Sit down on the ground between the open door and the door sill.
4.) Use a 3/8” ratchet, 12” extension, 3/8” universal adapter, and a ½” socket. If you have access to a ½” Snap On semi deep universal socket, that is even better. The studs stick out enough that a deeper socket works better.
5.) Remove all 4 nuts and save them. The booster may have metric nuts and replacing them can be tricky.
6.) Wiggle the booster out and up to get it past the master cylinder.
7.) Note the push rod and its adjustment. The new booster may require some adjusting. Too much adjustment and the brakes drag. Too little adjustment and the pedal hits the floor before you develop full braking power.
8.) Reassemble in reverse order, be prepared to bleed the brakes if you had to disconnect the master cylinder brake lines.
 
You must log in or register to reply here.

Similar threads

W
Front ATS brakes with Taurus rear brakes. Full parts needed?
  • Wagonized
  • Sep 24, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
308
Fox 5.0 Mustang Tech Sep 25, 2026
General karthief
J
Wheels-Tires Need Some Help - Brakes Upgrade/Wheel fitment
  • jaygee15
  • Dec 8, 2025
  • Fox 5.0 Mustang Tech
  • 3 4 5
Replies
85
Views
4K
Fox 5.0 Mustang Tech Oct 6, 2026
jaygee15
J
F
Electrical Foxbody wiring harness 2.3 to v8 swap
  • Foxbodyjake
  • Mar 23, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
26
Views
1K
Fox 5.0 Mustang Tech Sep 7, 2026
Kleinjj27
K
D
Mustang not starting
  • Dawry Ramos
  • Sep 12, 2026
  • 2015 - 2023 Specific Tech
Replies
10
Views
420
2015 - 2023 Specific Tech Oct 3, 2026
Dawry Ramos
D
C
Help with manual conversion
  • CPH89LX
  • Aug 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
20
Views
722
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 27, 2026
2000xp8
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?