• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Broken rocker arm bolt?

  • Thread starter Thread starter meangreen92
  • Start date Start date Dec 20, 2007
M

meangreen92

New Member
Aug 25, 2004
13
0
1
Dec 20, 2007
#1
  • Dec 20, 2007
  • #1
My car started blowing grey smoke today and idling like crap. I pulled off the valve cover to discover that one of the bolts holding the rocker on had broke. The car still has e7s and the stock 5/16 rockers. I put in a Crane 2020 (530 lift 204/208 duration) in last year and have not had any problems until now. About a month ago I put in new stock rockers since the stock one were so worn. I'm starting to think that the old worn rockers may have been what kept this from happening. I replaced the bolt after spending hours trying to get that damn broken bolt out but now I'm blowing gray smoke and I think the same thing is going to happen again as it getting louder again. Any ideas or suggestions would be greatly appreciated.
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Dec 20, 2007
#2
  • Dec 20, 2007
  • #2
get a set of roller rockers and set them up properly
 

jtfairlane

New Member
Mar 5, 2006
468
3
0
Dec 20, 2007
#3
  • Dec 20, 2007
  • #3
meangreen92 said:
My car started blowing grey smoke today and idling like crap. I pulled off the valve cover to discover that one of the bolts holding the rocker on had broke. The car still has e7s and the stock 5/16 rockers. I put in a Crane 2020 (530 lift 204/208 duration) in last year and have not had any problems until now. About a month ago I put in new stock rockers since the stock one were so worn. I'm starting to think that the old worn rockers may have been what kept this from happening. I replaced the bolt after spending hours trying to get that damn broken bolt out but now I'm blowing gray smoke and I think the same thing is going to happen again as it getting louder again. Any ideas or suggestions would be greatly appreciated.
Click to expand...

The Crane 2020 has 208/216 duration at .050" lift, not 204/208.

Did you replace the springs on the E7TE heads at the same time, or are you still running stock springs?

The recommended matching spring for that cam is Crane # 99841,and has 118lbs on the seat at a 1.950 installed height, 375lbs open at 1.380, and 457 spring rate.

If you are still using the stock E7TE heads, than you are only getting approximately 80lbs on the seat and around 215lbs open. The result of using stock springs with that kind of a cam, would be terrible valvetrain stability and harmonics, and could undoubtedly lead to busted rocker bolts (they are only 5/16" after all) and valve float, among other wear issues.

Lots of people just slap a cam in the block and pay no attention to the valve springs, which are absolutely critical. Are you one of those people?
 
M

meangreen92

New Member
Aug 25, 2004
13
0
1
Dec 20, 2007
#4
  • Dec 20, 2007
  • #4
jtfairlane said:
The Crane 2020 has 208/216 duration at .050" lift, not 204/208.

Did you replace the springs on the E7TE heads at the same time, or are you still running stock springs?

The recommended matching spring for that cam is Crane # 99841,and has 118lbs on the seat at a 1.950 installed height, 375lbs open at 1.380, and 457 spring rate.

If you are still using the stock E7TE heads, than you are only getting approximately 80lbs on the seat and around 215lbs open. The result of using stock springs with that kind of a cam, would be terrible valvetrain stability and harmonics, and could undoubtedly lead to busted rocker bolts (they are only 5/16" after all) and valve float, among other wear issues.

Lots of people just slap a cam in the block and pay no attention to the valve springs, which are absolutely critical. Are you one of those people?
Click to expand...

Yes 208/216 thats what I meant and no I am not one of "those people" thank you very much. I bought Crane cams 444212 which came with the springs. Like I said I have been running this thing for about a year with any problem. The stock springs were were so worn out it felt like an ignition miss. I thought I might as well put a cam in since it was getting new valve springs. I'm not retarded. I'm just asking for help.
 
You must log in or register to reply here.

Similar threads

8
Electrical Crank-no start ... no spark ... no injector pulse, was it something I did? (redux)
  • 85gtCOBRA
  • Oct 28, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
683
Fox 5.0 Mustang Tech Oct 29, 2025
85gtCOBRA
8
Engine adjust roller rockers on new 393
  • maxine-70
  • Dec 27, 2023
  • Fox 5.0 Mustang Tech
Replies
16
Views
3K
Fox 5.0 Mustang Tech Dec 30, 2023
AeroCoupe
Place to Avoid: Jamison Auto Group in Gulfport, MS
  • D Durden
  • Oct 20, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • 2 3
Replies
46
Views
4K
1965 - 1973 Classic Mustangs -General/Talk- Jul 16, 2026
Noobz347
W
Blue smoke..
  • Wicked_Rpm
  • Aug 11, 2024
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
567
1996 - 2004 SN95 Mustang -General/Talk- Aug 14, 2024
weendoggy
What in gods green earth happend to my N/A 2.3?
  • Piranahbite
  • Mar 24, 2024
  • 2.3L (N/A & Turbo) Tech
Replies
8
Views
2K
2.3L (N/A & Turbo) Tech Jun 1, 2024
Piranahbite
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?