Chattering noise while in gear

Bite_ME

New Member
Apr 22, 2008
29
0
0
I have a 87 mustang gt with a 84 t-5 tranny, It's been runnning fine now for about 8 months since I got the car. Just today noticed a slight chattering noise while I am in any gear but not in neutral. As I drove it home ( about 1 mile away) it got louder as I pulled into my driveway. I got under the car and the noise is coming from the clutch area sounds now like some beans in a can. Anyone know what this can be?
 
I can hear the noise while the car is in idle or in gear, but as soon I as I press down on the clutch it goes away. As soon as it stops raining outside I am gonna drop the tranny and bellhousing, as the noise seems to be coming from inside the bellhousing.
 
Well I started working on it today I got the driveshaft and crossmember off but since this is my first time taking the tranny and bellhousing off. I ran into some problems first the top bolts of the tranny are nearly impossible to get to, I am thinking I should just drop it down with the bellhousing since those bolts are easier to get too. Can I do that? Which now looking at the bellhousing , the starter and clutch cable even with reading the instructions on how to remove them thru the haynes manual seem a pain. The starters top bolt is the one I can't get off and the clutch cable well I hope someone can better explain these instructions : Lift the clutch pedal to its uppermost position to disengage the pawl and quadrant. Push the quadrant forward, unhook the cable and allow the quadrant to slowly swing rearward. I have searched but haven't found on how to do this.
 
well first off it isn't ur through out bearing, ur linkage could be off or u have contaminants on ur clutch disc or u could have a warped flywheel or press plate. just be sure when u put it back together u have a dowel to like up ur pilot bearing with ur clutch or u will have some problems
 
it almost sounds like a loose or broken clutch/ possibly a broken or loose pressure plate... as for the bell housing bolts.. a socket and LOOOONG extension should do fine.. and for the starter pretty much the same thing... i know its your first time so getting ziplock bags an labeling them is not a bad idea either.... you can also take the trans out of the bellhousing then take the bellhousing off the engine second... if for some reason you do decide to take the clutch/pressure plate/ release bearing off make SURE you loc-tite them and torque to specs..... just to save you a headache...
 
Got the bellhousing with the transmission attached off and took it to the transmission shop today, I should find out tomorrow if something is wrong with it after they tear it down. I got the starter off by removing the passenger wheel off and as for the clutch cable I stuck a long screwdriver and pushed the clutch fork back and removed the cable that way. If the tranny is messed up, I am already looking at getting this tranny off a 90 gt at a junkyard. Is there any simple things that I should do to the tranny and engine while I am at this stage like gaskets ie.
 
well first off it isn't ur through out bearing, ur linkage could be off or u have contaminants on ur clutch disc or u could have a warped flywheel or press plate. just be sure when u put it back together u have a dowel to like up ur pilot bearing with ur clutch or u will have some problems

man, you make my head hurt. First of all, take more time typing. READ what you post, so it's more legible!!! Second, i've seen you give bad advice in multiple posts, this one including.

LOL, linkage!!! This isn't a 66 mustang, it's a cable driven fox mustang, no linkage so to say.

If it was a noise that went away with just slight pedal pressure on the clutch, then your problem was simply a misadjusted clutch cable. Tighten more slack out of it and you'll be fine.

second of all, I wouldn't spend a dime on tha 84 t5. They're a ton weaker than the 85+ units. If you have access to a v8 t5 like you mentioned from an 85+ mustang, I'd jump on it.
 
Well the shop torn it down and said it was the tranny, (cluster gear) I don't plan on putting any money on this transmission as it is not worth it. Also the transmission that I was gonna get I found out right before I paid for it that it is for a 1987 4cyl mustang. I am trying to figure out if I have to get the whole trans and bellhousing or the bellhousing that I have would work with a WC T-5, the numbers on the bellhousing are E6ZR-6394-AA
 
that bell will work fine with a wc or 4 cyl trans.

if you can get that 4 cyl trans cheap enough, you could consider running it. They're strong enough to last quite some time. If you do, use a diesel ranger pilot bearing and all will be golden.

keep in mind, though that that non wc trans you had has a 2.95 first, and the 4 cylinder trans has a 3.95 first, so if you used the 4 cyl, it would be like adding a butt load of gear to your ride. Fine if you're not running gear out back now.

what SPECIFICALLY did they say was wrong with the cluster?? the cluster is a one piece solid shaft with NO moving parts, save the replaceable bearings at either side. I could only imagine maybe a tooth or two broken off???

Go to the shop and ASK to see the bad cluster, I'd be skeptical until you see it with your own eyes.