• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Chattering noise while in gear

  • Thread starter Thread starter Bite_ME
  • Start date Start date Aug 17, 2008
B

Bite_ME

New Member
Apr 22, 2008
29
0
0
Aug 17, 2008
#1
  • Aug 17, 2008
  • #1
I have a 87 mustang gt with a 84 t-5 tranny, It's been runnning fine now for about 8 months since I got the car. Just today noticed a slight chattering noise while I am in any gear but not in neutral. As I drove it home ( about 1 mile away) it got louder as I pulled into my driveway. I got under the car and the noise is coming from the clutch area sounds now like some beans in a can. Anyone know what this can be?
 

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Aug 17, 2008
#2
  • Aug 17, 2008
  • #2
My cousins truck did something like that and it was a broken spring on the clutch plate
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Aug 17, 2008
#3
  • Aug 17, 2008
  • #3
Just a curious question, but do you still have cats? The spot welds that hold the heat shields tend to break and they'll sound exactly like your description.
 
B

Bite_ME

New Member
Apr 22, 2008
29
0
0
Aug 17, 2008
#4
  • Aug 17, 2008
  • #4
Yea I removed my cats about three weeks ago after I put my shorty headers and off road h-pipe. It sounds just like that by way, as I have had cats go out before.
 
B

Bite_ME

New Member
Apr 22, 2008
29
0
0
Aug 18, 2008
#5
  • Aug 18, 2008
  • #5
I can hear the noise while the car is in idle or in gear, but as soon I as I press down on the clutch it goes away. As soon as it stops raining outside I am gonna drop the tranny and bellhousing, as the noise seems to be coming from inside the bellhousing.
 

jhonda

Member
Jul 22, 2003
125
1
16
Huntersville NC
Aug 19, 2008
#6
  • Aug 19, 2008
  • #6
I would say its the throw out bearing
 
B

Bite_ME

New Member
Apr 22, 2008
29
0
0
Aug 19, 2008
#7
  • Aug 19, 2008
  • #7
Well I started working on it today I got the driveshaft and crossmember off but since this is my first time taking the tranny and bellhousing off. I ran into some problems first the top bolts of the tranny are nearly impossible to get to, I am thinking I should just drop it down with the bellhousing since those bolts are easier to get too. Can I do that? Which now looking at the bellhousing , the starter and clutch cable even with reading the instructions on how to remove them thru the haynes manual seem a pain. The starters top bolt is the one I can't get off and the clutch cable well I hope someone can better explain these instructions : Lift the clutch pedal to its uppermost position to disengage the pawl and quadrant. Push the quadrant forward, unhook the cable and allow the quadrant to slowly swing rearward. I have searched but haven't found on how to do this.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Aug 19, 2008
#8
  • Aug 19, 2008
  • #8
Are you sure it's an 84 t-5?
 

putnam88

Member
Aug 2, 2006
102
0
17
tavares
Aug 19, 2008
#9
  • Aug 19, 2008
  • #9
well first off it isn't ur through out bearing, ur linkage could be off or u have contaminants on ur clutch disc or u could have a warped flywheel or press plate. just be sure when u put it back together u have a dowel to like up ur pilot bearing with ur clutch or u will have some problems
 
B

Bite_ME

New Member
Apr 22, 2008
29
0
0
Aug 19, 2008
#10
  • Aug 19, 2008
  • #10
I am not 100 % sure it is a 84 T-5 because I am going off by just the metal tag that was on it
 

mustangmike6996

5 Year Member
Nov 10, 2005
483
6
29
clinton twp, MI
Aug 19, 2008
#11
  • Aug 19, 2008
  • #11
it almost sounds like a loose or broken clutch/ possibly a broken or loose pressure plate... as for the bell housing bolts.. a socket and LOOOONG extension should do fine.. and for the starter pretty much the same thing... i know its your first time so getting ziplock bags an labeling them is not a bad idea either.... you can also take the trans out of the bellhousing then take the bellhousing off the engine second... if for some reason you do decide to take the clutch/pressure plate/ release bearing off make SURE you loc-tite them and torque to specs..... just to save you a headache...
 
B

Bite_ME

New Member
Apr 22, 2008
29
0
0
Aug 20, 2008
#12
  • Aug 20, 2008
  • #12
Got the bellhousing with the transmission attached off and took it to the transmission shop today, I should find out tomorrow if something is wrong with it after they tear it down. I got the starter off by removing the passenger wheel off and as for the clutch cable I stuck a long screwdriver and pushed the clutch fork back and removed the cable that way. If the tranny is messed up, I am already looking at getting this tranny off a 90 gt at a junkyard. Is there any simple things that I should do to the tranny and engine while I am at this stage like gaskets ie.
 
V

v8only

Active Member
Jul 3, 2003
2,378
22
49
Aug 21, 2008
#13
  • Aug 21, 2008
  • #13
putnam88 said:
well first off it isn't ur through out bearing, ur linkage could be off or u have contaminants on ur clutch disc or u could have a warped flywheel or press plate. just be sure when u put it back together u have a dowel to like up ur pilot bearing with ur clutch or u will have some problems
Click to expand...

man, you make my head hurt. First of all, take more time typing. READ what you post, so it's more legible!!! Second, i've seen you give bad advice in multiple posts, this one including.

LOL, linkage!!! This isn't a 66 mustang, it's a cable driven fox mustang, no linkage so to say.

If it was a noise that went away with just slight pedal pressure on the clutch, then your problem was simply a misadjusted clutch cable. Tighten more slack out of it and you'll be fine.

second of all, I wouldn't spend a dime on tha 84 t5. They're a ton weaker than the 85+ units. If you have access to a v8 t5 like you mentioned from an 85+ mustang, I'd jump on it.
 
B

Bite_ME

New Member
Apr 22, 2008
29
0
0
Aug 21, 2008
#14
  • Aug 21, 2008
  • #14
Well the shop torn it down and said it was the tranny, (cluster gear) I don't plan on putting any money on this transmission as it is not worth it. Also the transmission that I was gonna get I found out right before I paid for it that it is for a 1987 4cyl mustang. I am trying to figure out if I have to get the whole trans and bellhousing or the bellhousing that I have would work with a WC T-5, the numbers on the bellhousing are E6ZR-6394-AA
 
V

v8only

Active Member
Jul 3, 2003
2,378
22
49
Aug 21, 2008
#15
  • Aug 21, 2008
  • #15
that bell will work fine with a wc or 4 cyl trans.

if you can get that 4 cyl trans cheap enough, you could consider running it. They're strong enough to last quite some time. If you do, use a diesel ranger pilot bearing and all will be golden.

keep in mind, though that that non wc trans you had has a 2.95 first, and the 4 cylinder trans has a 3.95 first, so if you used the 4 cyl, it would be like adding a butt load of gear to your ride. Fine if you're not running gear out back now.

what SPECIFICALLY did they say was wrong with the cluster?? the cluster is a one piece solid shaft with NO moving parts, save the replaceable bearings at either side. I could only imagine maybe a tooth or two broken off???

Go to the shop and ASK to see the bad cluster, I'd be skeptical until you see it with your own eyes.
 
You must log in or register to reply here.

Similar threads

D
Drivetrain car still rolling while in gear and off
  • dqureshi06
  • Jan 24, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
326
Fox 5.0 Mustang Tech Jan 24, 2026
General karthief
2000 GT-Front Brakes Not Releasing
  • stormsedge
  • Aug 7, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
5
Views
248
1996 - 2004 SN95 Mustang -General/Talk- Aug 7, 2026
Bronco2fan
B
T
Drivetrain TREMEC TKX 1–2 Grinding Issue at ~4,000 Miles + Poor Warranty/Customer Service Experience
  • Ttopfoxguy
  • Oct 10, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
319
Fox 5.0 Mustang Tech Oct 15, 2026
JMG9350
J
C
Drivetrain T-5 transmission issue
  • Ch3No2
  • Jul 11, 2025
  • Fox 5.0 Mustang Tech
Replies
3
Views
493
Fox 5.0 Mustang Tech Jul 18, 2025
2000xp8
2008 Mustang Bullitt stuck in Fifth gear
  • Jester67
  • Jul 15, 2025
  • 2005 - 2014 S-197 Mustang -General/Talk-
Replies
10
Views
605
2005 - 2014 S-197 Mustang -General/Talk- May 27, 2026
Jester67
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?