• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

diffrent brand of lifters on each side of engine

  • Thread starter Thread starter green
  • Start date Start date Jan 12, 2006

green

New Member
Apr 26, 2003
291
0
0
Jan 12, 2006
#1
  • Jan 12, 2006
  • #1
hey, hows it going. i have a lifter ticking on my mustang at start ups. the ticking is coming from the passenger side of the car. i had all 16 lifters replaced when i rebuilt my engine 3 years ago. should i replace all 16 lifters or is it all right to just replace all 8 lifters on the passenger side of the engine. i will probally buy ford racing lifters, but i do not know what kind of lifters the engine rebuilder put in my engine. thanks
 
H

hrspwrjunkie

Member
Dec 15, 2004
165
0
18
Jan 12, 2006
#2
  • Jan 12, 2006
  • #2
Well, I would personally buy a full set of Ford Racing lifters and be done with it, however, it is little known knowledge that there are a very limited number of automotive manufacturers and chances are the lifters you have in the engine are the same ones provided by Ford Racing even though could have been provided by a different "brand."

Ryan

green said:
hey, hows it going. i have a lifter ticking on my mustang at start ups. the ticking is coming from the passenger side of the car. i had all 16 lifters replaced when i rebuilt my engine 3 years ago. should i replace all 16 lifters or is it all right to just replace all 8 lifters on the passenger side of the engine. i will probally buy ford racing lifters, but i do not know what kind of lifters the engine rebuilder put in my engine. thanks
Click to expand...
 
I

iwashmycar

20+ Year Stangneter
Apr 7, 2004
1,236
1
39
Columbus, Ohio
Jan 12, 2006
#3
  • Jan 12, 2006
  • #3
ive got a little of that ticking too..can you just tighten them down a bit as i heard once?..i really dont know
 
2

2002BLGT

Well-Known Member
Dec 18, 2003
2,945
4
59
Bedford VA
Jan 12, 2006
#4
  • Jan 12, 2006
  • #4
pull it apart and make sure they all have the bleed hole facing upwards if its not spin them around and put it back together , I had alot of ticking when I put my HCI on and then changed intakes , didnt even realize they had an air bleed in the lifters but there is a notch in each lifter only on one side of them and they must be facing up for the air to escape easily .......when i pulled mine down to change intakes I checked the lifters and sure enough 8 of them were upside down , put them in right side up and put it back together and now no more tick .....if you pull it apart and this isnt the problem go ahead and get a whole new set and check everything else for wear ......
 

Black1987Stang

Active Member
Aug 22, 2004
1,422
0
37
Jersey Shore
Jan 13, 2006
#5
  • Jan 13, 2006
  • #5
2002BLGT said:
pull it apart and make sure they all have the bleed hole facing upwards if its not spin them around and put it back together , I had alot of ticking when I put my HCI on and then changed intakes , didnt even realize they had an air bleed in the lifters but there is a notch in each lifter only on one side of them and they must be facing up for the air to escape easily .......when i pulled mine down to change intakes I checked the lifters and sure enough 8 of them were upside down , put them in right side up and put it back together and now no more tick .....if you pull it apart and this isnt the problem go ahead and get a whole new set and check everything else for wear ......
Click to expand...


Ive heard that doesnt matter...My old motor and my friends had the holes in all mixed up orders, just randomly placed and they didnt have have any ticks. That is how oil gets into the lifter, i have a spare lifter in front of me and thats the only way i can see for the pressurized oil to get in, and since its pressurized whether the hole is in the front or back its still going to get in the hole. Thats my opinion anway, I doubt this would be his case since its been fine for the last 3 years and now it just showed up, Just for my memory I put all the holes pointing the lifter galley when i put my motor together.
 
S

SmockDoiley

New Member
Jun 14, 2003
1,591
2
0
San Diego, CA
Jan 13, 2006
#6
  • Jan 13, 2006
  • #6
Im surprised you even have a bad lifter, those things hardly ever go bad. Anyways, if your getting new lifters, avoid Ford Racing crap because everything they make is outsourced reboxed crap. Crane makes these replacement lifters and I think they are the cheapest on the market.
 
You must log in or register to reply here.

Similar threads

H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
311
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
D
Rockers, lash adjusters and timing: help with parts (4.6 2v)
  • dvigAtel
  • Nov 1, 2025
  • Other Auto Tech
Replies
0
Views
252
Other Auto Tech Nov 1, 2025
dvigAtel
D
9
Forced Induction Prepping for supercharger on non-stock build
  • 91fox427
  • Nov 25, 2025
  • Fox 5.0 Mustang Tech
Replies
7
Views
428
Fox 5.0 Mustang Tech Jan 5, 2026
Qtrhrse23
Q
P
Engine Mysterious coolant leak at back of engine
  • palerider94
  • Jan 18, 2026
  • Fox 5.0 Mustang Tech
Replies
1
Views
195
Fox 5.0 Mustang Tech Jan 19, 2026
AeroCoupe
9
Engine Donor '00 Mountaineer meet '91 Fox
  • 91firecracker
  • May 11, 2026
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
41
Views
930
Fox 5.0 Mustang Tech May 28, 2026
91firecracker
9
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?