• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Distributor Gear Removal??

  • Thread starter Thread starter 90lxcoupe
  • Start date Start date May 4, 2006

90lxcoupe

20+ Year Stangneter
Oct 7, 2003
3,596
350
134
May 4, 2006
#1
  • May 4, 2006
  • #1
How do i remove the gear from the distributor, i removed the pin, and the gear wont come off, is there a special kind of trick or should it just slide right off? cause its definitly stuck on there. would some penetrating oil help?
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
May 4, 2006
#2
  • May 4, 2006
  • #2
It's pressed on bro. Take it to a machine shop.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
May 5, 2006
#3
  • May 5, 2006
  • #3
You could use a bearing splitter, or my buddy MM found a special tool just for doing this. It's about 55-60 bucks though.

Good luck.
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
May 5, 2006
#4
  • May 5, 2006
  • #4
You first have to drive the roll pin out of the dist, then I use a little heat and it comes off. When you put the new ggear on you should rotate the pin hole 90 dgerees and re-drill the shaft, measure twice drill and mount once.
 

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
May 5, 2006
#5
  • May 5, 2006
  • #5
You can tap them off. Put the dist in a vice, upside down, with the gear on the top of the jaws and tap the shaft out. Be careful not to head over the end of the shaft.
 

90lxcoupe

20+ Year Stangneter
Oct 7, 2003
3,596
350
134
May 5, 2006
#6
  • May 5, 2006
  • #6
so i need a new gear? if this is the case im gonna return the module and just spend 20 bucks more on a distributor.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
May 6, 2006
#7
  • May 6, 2006
  • #7
No, you press the gear off to remove the PIP components. Then once the new stuff is on, you put the gear back on.

Rick, why do you redrill a new hole?
 

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
May 6, 2006
#8
  • May 6, 2006
  • #8
You need to remove the rolled pin, press or tap the gear off. Installation is the reverse.

If you are carefull, you can use the pin over again.

I would not drill a new hole for the original gear, as it would weaken the shaft, in my opinion. I have had no trouble getting the gears off and on several of my dist's.
 

TrophyHead

15 Year Member
Mar 18, 2003
1,195
11
49
PA
May 6, 2006
#9
  • May 6, 2006
  • #9
Use a brass hammer.
 
You must log in or register to reply here.

Similar threads

Electrical Code 29 again
  • Creomod
  • Jul 31, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
394
Fox 5.0 Mustang Tech Aug 3, 2026
Creomod
F
Fox 1990 Mustang GT 5.0 A9L – Engine suddenly shuts off but immediately restarts when key turned
  • FishermansFriend
  • Aug 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
695
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 30, 2026
General karthief
Resolved Does anybody recognise this distributor gear?
  • x_man586
  • Jun 4, 2025
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
766
Fox 5.0 Mustang Tech Jun 24, 2025
x_man586
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
735
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
3.08 gears with a manual trans
  • limp
  • Aug 27, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2 3
Replies
43
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 14, 2026
Qtrhrse23
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?