• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

EGR plate

  • Thread starter Thread starter Roland69
  • Start date Start date Nov 1, 2007

Roland69

Sergeant Tangnet
Sep 17, 2005
2,867
3
58
Port Elgin, Ontario
Nov 1, 2007
#1
  • Nov 1, 2007
  • #1
has anyone ever ported/honed the stock egr plate to match a bigger than stock throttle body. I just got a gt40 intake with a 70mm TB and they match perfect but now I will need a egr plate to match. anyone done this to a stock plate, is there even enough meat in one to take that much out of one. I would try to use a cyl hone and keep a close eye on the measurements as I go.
 

bloopbloob

Member
Sep 27, 2006
578
4
16
Alberta
Nov 2, 2007
#2
  • Nov 2, 2007
  • #2
i havent done it to an egr, but i port matched my intake to my 70mm egr spacer. Just trace your tb onto your egr and have a look. you should be able to tell how much meat will be left if you grind it to match... what is it stock? 58mm??
 

Roland69

Sergeant Tangnet
Sep 17, 2005
2,867
3
58
Port Elgin, Ontario
Nov 3, 2007
#3
  • Nov 3, 2007
  • #3
not sure I haven't measured
 

PUNISHER RACING

Active Member
Aug 27, 2007
1,124
0
36
FORD CITY, PA.
Nov 3, 2007
#4
  • Nov 3, 2007
  • #4
yes it can be done have it machined to 72 mm
 

Roland69

Sergeant Tangnet
Sep 17, 2005
2,867
3
58
Port Elgin, Ontario
Nov 3, 2007
#5
  • Nov 3, 2007
  • #5
why 72....wouldn't that leave a little lip
 

NIKwoaC

中國製造
15 Year Member
Oct 31, 2006
5,525
943
214
Chengdu Province
Nov 3, 2007
#6
  • Nov 3, 2007
  • #6
I have read that the EGR spacer should be 2 or 3 mm bigger than the TB, if any bigger at all. Make sure the intake opening matches the 72mm egr if you go that route.

I once tried to mill the egr spacer out to 70mm on an old unit... the Ford casting has an oddly tapered bore, make sure you check both sides of the egr so once you bore the hole it still matches up with both the TB and upper intake once its all bolted on.
 

Roland69

Sergeant Tangnet
Sep 17, 2005
2,867
3
58
Port Elgin, Ontario
Nov 3, 2007
#7
  • Nov 3, 2007
  • #7
so I should bore the intake opening to 72 and buy or make a 72 mm EGR plate, and leabt the TB 70mm. That don't make much sence why not a strait 70mm straight through
 
You must log in or register to reply here.

Similar threads

9
Engine Donor '00 Mountaineer meet '91 Fox
  • 91firecracker
  • May 11, 2026
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
41
Views
1K
Fox 5.0 Mustang Tech May 28, 2026
91firecracker
9
Engine Hiccup at full throttle
  • keel
  • Jun 2, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
31
Views
1K
Fox 5.0 Mustang Tech Jul 30, 2026
keel
Idle issues….again.
  • Nostang25
  • Sep 7, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
239
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 7, 2025
AeroCoupe
S
Fuel ‘88 GT Runs Rich Cold — Fixes Itself When I Unplug Sensors (ECT, MAF, O2, etc.)
  • Sufarry
  • Nov 6, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
1K
Fox 5.0 Mustang Tech Nov 9, 2025
Mustang5L5
1
Engine 91 mustang 302 Low acceleration car backfires pops and acts like it doesn’t want to take fuel
  • 1991Fox5.0
  • Oct 4, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Oct 6, 2025
1991Fox5.0
1
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?