explain stroker motors...

Have you heard the quote: "There is no replacement for displacement?"

A stroker motor adds displacement by changing the amount of travel that a piston is subjected to in 1 revolution. This is accomplised by adding a longer rod and crank with the corresponding throw. And as Willys1 put it, by adding the "longer stroke=more horespower"


Just some background for you to help understand the concept: Take two motors with 347 cubic inches for thinking purposes

A motor with a short stroke and large diameter pistons will rev very fast and not produce a lot of torque.

A motor with a long stroke and smaller pistons will rev slower (slightly) and will build more torque

Torque is a measure of an objects resitance to twist or rotate

Now, HP is a measure of torque, so the more torque your motor has, the more hosepower you have (so to speak) This then negates the issue of reving slower.
 
srothfuss said:
Have you heard the quote: "There is no replacement for displacement?"

A stroker motor adds displacement by changing the amount of travel that a piston is subjected to in 1 revolution. This is accomplised by adding a longer rod and crank with the corresponding throw. And as Willys1 put it, by adding the "longer stroke=more horespower"


Just some background for you to help understand the concept: Take two motors with 347 cubic inches for thinking purposes

A motor with a short stroke and large diameter pistons will rev very fast and not produce a lot of torque.

A motor with a long stroke and smaller pistons will rev slower (slightly) and will build more torque

Torque is a measure of an objects resitance to twist or rotate

Now, HP is a measure of torque, so the more torque your motor has, the more hosepower you have (so to speak) This then negates the issue of reving slower.

Yes and No.... The additional displacement is a byproduct of the extra travel that the piston must do as a result of the longer stroke. There may be some additional torque as a result of the extra piston travel but it is negligable. The majority of the extra torque on a stroker motor comes from the mechanical advantage provided by the stroked crank.

4cylenginecranka4rx.webp


Look at the two red lines. The distance between them is the length of the pivot for our crank "lever". When the crank lobe is horizontal, you can imagine its mechanical advantage. Lengthen the distance between those red lines and apply the same force to push the lever "down". With a longer crank though the same amount of force is applied to the piston head, you gain a greater mechanical advantage on the "lever" and end up with more torque on the output shaft of the crank.

You can shorten the piston rods to reduce the amount of travel on the pistons and still end up with a significant mechanical advantage. The RPM increase (mentioned above) comes from using a longer rod and increasing the amount of rotation of the crank vs. the movement of the piston.

In other words:

Given the same stoke of the crank -- The longer the rod to "more crank" travel you get, and the quicker the crank will rotate. Shorten the rod to reduce piston travel and you end up with a higher rod angle and less piston travel. The longer rods are also more effecient and make more use of the expended energy from the cumbustion mixture. The longer travel of the piston allows for longer burn of the combustion mixture meaning that there's more time and energy spent by that mixture in pushing the piston downward to rotate the crank. A significant amount of power is picked up as a result of that as well.

With the exception of some down force lost due to increased piston angle, torque is not much affected by the shorter rod and less piston travel. The same amount of energy is still being expended to push that piston downward and the same mechanical advatage of the crank is still there (again, minus a small amount due to the increased rod angle). Horse power is much more significantly affected. Increasing the rod length and piston travel will have the greatest effect on rev capability and HP.

Reminder: HP = Torque at RPM

This last pic may help to visualize the post.

4cylenginecrank2xq.webp


Longer rods are used to deacrease the amount of rod angle in a motor. They're also more effecient at applying the energy expended on the piston head and converting that energy to linear motion to push the rod lobe as close to "straight down" (in relation to the crank centerline) as possible.
 

Attachments

  • 4cylenginecranka4rx.webp
    4cylenginecranka4rx.webp
    2.8 KB · Views: 179
  • 4cylenginecrank2xq.webp
    4cylenginecrank2xq.webp
    2.8 KB · Views: 254
srothfuss said:
I was trying to keep it simple for the guy... I like the diagrams / pictures Daggar

Yeah, I got the got the spirit of your post. That's why I quoted you; There's good stuff there (it made me think). I just wanted to more or less explain the interrelation of where torque vs. the horsepower is obtained.

High torque motors (and strokers and assuming two motors of the same displacement) would have a long stroke and short rod and piston travel (and ultimately less HP -- rev range would also be lower) whereas high horsepower motors would generally have a much longer rod and more piston travel on the same sized crank.

Again though... this is taking the actual displacement of the motor out of the equation and making them equal in that regard. 5ohs have what I consider to be a good balance. Modular motors tend to lean more towards HP production over torque production (shorter crank throws and relatively long rods).
 
Daggar,you didnt mention how much power and torque you also gain by increasing the bore size.

Also,the longer rod motors tend to have a short piston compression hight,which means a lighter piston.But,the longer rod also looses a little of its advantage at higher rpms,were the motor needs the piston pulled away from the head face/combustion chamber faster.Thats especialy true with power adder cars because of the accelerated burn rate.You can also use a piston with an off set wrist pin and a shorter rod to get a better rod ratio and still have a shorter dwell time at TDC/BDC.

And I really dont see a smaller stroke motor reving any fast than a long stroke IF the total wieght of the parts were the same.
 
bluevenom867 said:
Daggar,you didnt mention how much power and torque you also gain by increasing the bore size...


There are many things I didn't mention. As with Strothfuss, covering every variable would require quite a lengthy post. We all know that boring a 302 .030 over (to a 306) nets a negligable increase whereas keeping the stock bore and increasing the length of the stroke and lengthening the travel of the piston nets us significant more gain in torque and HP.

bluevenom867 said:
And I really dont see a smaller stroke motor reving any fast than a long stroke IF the total wieght of the parts were the same.

Again, rev capability is going to have more to do with rod length and piston travel in a given motor than will the crank stroke (combinations of both aside for the purpose of the discussion). The amount of time the combustion mixture is allowed to exert force on the piston head is a major factor as to how fast and efficiently the crank is forced to rotate (yes, rod angle is a factor in this).
 
Daggar said:
There are many things I didn't mention. As with Strothfuss, covering every variable would require quite a lengthy post. We all know that boring a 302 .030 over (to a 306) nets a negligable increase whereas keeping the stock bore and increasing the length of the stroke and lengthening the travel of the piston nets us significant more gain in torque and HP.

Well,yes .030 over on a 302 aint gonna pick up much,but .060 or .125 over on a 302/351W sure would (assuming an SVO/Dart block).But even at .030 over,it does unsroud the valves and pick up a couple tenths of a point of compression.


Daggar said:
Again, rev capability is going to have more to do with rod length and piston travel in a given motor than will the crank stroke (combinations of both aside for the purpose of the discussion). The amount of time the combustion mixture is allowed to exert force on the piston head is a major factor as to how fast and efficiently the crank is forced to rotate (yes, rod angle is a factor in this).

Thats was more for anyone thinking that because a stroker crank was heavier that it would be hard to get it moving.

And the fact that out of four strokes (intake,compression,power,exhaust)only one of them actualy applise usable force on the crank.

This is one thing that I think can make a smaller motor able to make high hp,is that the amount of power required to draw the charge in and compress it,and then push the exhaust out it all reduced compared to the bigger motor.
 
bluevenom867 said:
Well,yes .030 over on a 302 aint gonna pick up much,but .060 or .125 over on a 302/351W sure would (assuming an SVO/Dart block).But even at .030 over,it does unsroud the valves and pick up a couple tenths of a point of compression.

Yet again... increasing the bore and surface area of the piston will provide more product in terms of torque than HP. Expending the same force in combustion on a larger surface area is also a mechanical advantage and will provide more downforce on the crank lobe and output shaft (just as a longer stroked crank would).
 
bluevenom867

How is it I don't have a screen name for you on any of the chat programs? This is the kind of thing I'd like talk about in depth and consider a lot more of the variables. It all makes for great discussion! :-)
 
cool. I knew the basics of a stroker motor ( longer rod and etc)

but i was thinking in my head, a high point for the old 289s was that they revved higher and faster right??

ok here is a weird question.
how would a 347 stroker act compared to a 351, assuming they have the same mods. Does the 351 have a longer rod than the 347?
 
Daggar said:
bluevenom867

How is it I don't have a screen name for you on any of the chat programs? This is the kind of thing I'd like talk about in depth and consider a lot more of the variables. It all makes for great discussion! :-)

What,like AIM?

Thats would be cool to talk about matter like this with you.

This new skin doesnt make you really want to post any lengthy post.

And Im kinda bad with spelling some words,so thats why my post arnt as um,advanced as yours?
 
bluevenom867 said:
What,like AIM?

Thats would be cool to talk about matter like this with you.

This new skin doesnt make you really want to post any lengthy post.

And Im kinda bad with spelling some words,so thats why my post arnt as um,advanced as yours?

Yeah... something like AIM (or whatever program you prefer).

As for the spelling... I often cheat and use a spell checker. hehe
 
Foxfan88 said:
cool. I knew the basics of a stroker motor ( longer rod and etc)

but i was thinking in my head, a high point for the old 289s was that they revved higher and faster right??

ok here is a weird question.
how would a 347 stroker act compared to a 351, assuming they have the same mods. Does the 351 have a longer rod than the 347?

Longer stroke, longer rod, larger piston, the works. What's more is that the 351 can be further stroked to make even MORE power.