good first mods

88Stangboy said:
I would stay away from nitrous, it shortens engine life, it's good for the track to improve e.t's but it definatly shortens engine life.

Nitrous will only shorten your engine life if you do not know how to use it. Same with any other power adder.

Once you start making all the power you want, don't forget a good set of sticky tires. All the power in the world means nothing if you can't put it to the ground.
 
350 hp and above on NA engine is not going to happen with simple cheap mods so if you want it, eventually you're going to have to pay for it.

Mods that improve perfomance but not hp are:

-Any kind of weight reduction (fiberglass hood, trunk, spare tire, jack etc.)
-Rearend Gears (3.55 or 3.73)
-Short shifter on a manual trans. or valve body upgrade on auto
-Adjust TPS voltage as close to .98 as possible (do a search for instructions)

Simple cheap first mods that will boost hp a little bit are:

-A good tune up using quality parts, FRPP, MSD, Accel (plugs, wires, cap, rotor, fuel filter)
-Remove air intake silencer (free)
-Put a K&N filter in the stock air box (25-30 bucks)
-Advance your timing to 12 or 14 deg. (free) (run premium gas if you go above 12)
-If you advance timing, up your fuel pressure a bit w/ an adj. FPR (60 bucks) and you'll get the same benefit as a chip for a lot cheaper.
-U/D pullies and electric fan if your alt. can handle it.
-A larger Throttle body, 65mm is all you'd need, but port the intake opening to match or it's basically worthless.
-70 or 76mm MAF depending on what your future modification plans are
-Shorty Headers and an H-Pipe. I'd use an aftermarket H with high flow cats since your mods up to this point don't require the elimination a ton of backpressure like an off road H would give.

At this point you're pretty much done with all the mildly inexpensive mods. The big stuff like H/C/I, nitrous, or poweradders usually comes next.
 
304billet said:
The only way to achieve 350fwhp NA is to swap out the heads, cam and intake. AFR165, TFS TW heads, RPM ll intake port matched, Comp Cam XE274HR, Accufab 65mm TB, PMAS 70mm, MAF, LT headers. Costs about $4K w/ labor.

u could also just thow a S-trim blower on it 10-12lbs of boost and hit 350rwhp. $4K.

If I had this choice I would do the blower.
RPM II is too big for a stock short block may be the RPM or Track heat
 
fastfox86 said:
350 hp and above on NA engine is not going to happen with simple cheap mods so if you want it, eventually you're going to have to pay for it.

Mods that improve perfomance but not hp are:

-Any kind of weight reduction (fiberglass hood, trunk, spare tire, jack etc.)
-Rearend Gears (3.55 or 3.73)
-Short shifter on a manual trans. or valve body upgrade on auto
-Adjust TPS voltage as close to .98 as possible (do a search for instructions)

Simple cheap first mods that will boost hp a little bit are:

-A good tune up using quality parts, FRPP, MSD, Accel (plugs, wires, cap, rotor, fuel filter)
-Remove air intake silencer (free)
-Put a K&N filter in the stock air box (25-30 bucks)
-Advance your timing to 12 or 14 deg. (free) (run premium gas if you go above 12)
-If you advance timing, up your fuel pressure a bit w/ an adj. FPR (60 bucks) and you'll get the same benefit as a chip for a lot cheaper.
-U/D pullies and electric fan if your alt. can handle it.
-A larger Throttle body, 65mm is all you'd need, but port the intake opening to match or it's basically worthless.
-70 or 76mm MAF depending on what your future modification plans are
-Shorty Headers and an H-Pipe. I'd use an aftermarket H with high flow cats since your mods up to this point don't require the elimination a ton of backpressure like an off road H would give.

At this point you're pretty much done with all the mildly inexpensive mods. The big stuff like H/C/I, nitrous, or poweradders usually comes next.
What he said, EXACTLY:nice:
 
ok heres what i wanna get and i wanna do it all at once. but i might hold off until i can get everything i want instead of doing some here some there. so i might have to get some more more money. i want the supercharger, gt40x turbo swirl heads, ford motor sports f303 cam, trick flow track heat intake, granitelli mass air and match the injectors, i shouldnt need a cold air intake because of the supercharger, 3.55 gears, short throw shifter, headers, off road x or h pipe, cat back exhaust and oher little odds and ends. ok so ill know what mass air to use, what size injectors should i use? would you use 30 lb's? should i re program the computer with the diablo motorsports tuner? i only want to run 6 lb's of boost at first.
 
It'll need to a be a blow-through design maf meter. Whoever brought out ProM makes them in 80mm size. You'll probably need 36lbs. injectors. Diablo doesn't do chips for 5.0s that I know of. You won't need a CAI, but Anderson Ford Motorsports makes them for superchargers and they usually add 20hp or so. You'll need to get a custom chip burned from a local tuner or buy a Tweecer, Anderson Ford Motorsport PMS, or go standalone such as a FAST system.
 
You'll definitely need more more money. 30 pounders should work for 6 psi. I'd go with a Pro-M MAF and spring for some better heads if you are already doing that much work and investing that much money all at once. You'll love it when you're done though.

OH, and thanks for the props fiveohblow.
 
no matter how much nitrous you use, its going to shorten your engine life somewhat. Ask any professional engine builder and you will hear the same. It may be 5,000miles or 50,000 miles depending on how much you use, it puts tremendous stress on your rod and main bearings. Of course if you build an engine to handle nitrous it will hold up much, much better. And don't forget about your clutch and drivline also, a stock T-5 is going to need a second look if you are planning on running 350hp.
 
mustangluvr8993 said:
ok and then what size throttle body should i use? 70 or 75mm?


Most (not all) naturally aspirated and small super charger setups will be fine with a 65mm / 70mm throttle body. I'd stay with the smaller of those two, but that is just me.
 
Yes thats true also, but not nearly as quickly as nitrous does. Ask anyone who knows about it, nitrous is hell on a stock engine, it just shortens engine life quicker than just about anything. Boost does to, but boost is not as nearly as violent as nitrous. Its just like when someone is walking on your back, its nice and easy, but have them jump up and down on you...see what im saying. I've pulled apart two engines that had nitrous ran through them, the bearings in both engines both looked like they had 200,000 miles on them, the engines had about 90,000 miles each, the wear shows....each engine had a 100hp shot on them. IMO i just don't prefer nitrous...its kinda cheater hp anyways...just my opinion though.