Head Dilema

1Slow90coupe

New Member
Oct 18, 2005
145
0
0
Here is the set up. I know the ??? has been asked a million times.

I have the following....
90 302 stock motor with
BBK CAI
Headers
Off road h pipe
MAC mufflers
355 gears
pro 5.0 shifter
drag radials
150 NX wet shot
elec fan
battery in trunk
sway bar removed
Best ET to date 12.52

I know I should be doing a little better than that, but I am not the best driver. I am consistent with my 12.5s though.

Over the winter I am going to swap the heads and cam. I do not have the $$$ to do the rest of the top end so that is where I am going to start. Thinking AFR 165's with a few of the extras(upgraded springs, and pollish work) with a E303 cam or maybe a little bigger. I still want decent idle.



Suggestions are welcome.

What would this get me? Last dyno was 308HP and 455ftlp tq to the wheels with the 150 shot. 206/3?? with out it.
 
Do not go with the e-cam. It's outdated. There are much better cams out there now, that still retain great idles, and make a lot more power. Those 165's flow hella good, so you'll want a rather aggressive cam to go with them. Somebody recommended a Crane 2030 or 2031 a long time ago to me. It's comparable to the tfs stage 1, which makes good power, but it does have a lopey idle. Just don't go with the e-cam, lol. It's notorious for causing idle issues anyway.
 
I agree with Chris, the FMS cams are good but there are better choices. I would also go with something else, i always feel like i am promoting the TFS cam, but it is a good cam and it is cheaper than the FMS cams. So you are not getting new lifters or pushrods? Are you getting a different intake? Those heads will be really restricted if you use the stock intake. Also, i think those are some pretty good times! ~Nick
 
mustangramair said:
I agree with Chris, the FMS cams are good but there are better choices. I would also go with something else, i always feel like i am promoting the TFS cam, but it is a good cam and it is cheaper than the FMS cams. So you are not getting new lifters or pushrods? Are you getting a different intake? Those heads will be really restricted if you use the stock intake. Also, i think those are some pretty good times! ~Nick

Thanks for the congrats.

Unfortunately I don't have the $$ right now to do the top end. I am just trying to find the best place to start. My thought was heads. More info on the TFS cam would be appreciated.
 
Here are the specs of the cam from the summit website.
Brand: Trick Flow Specialties
Product Line: Trick Flow Track Heat Camshafts for Ford
Cam Style: Hydraulic roller tappet
Basic Operating RPM Range: 2,500-6,500 RPM
Intake Duration 050 inch Lift: 221
Exhaust Duration 050 inch Lift: 225
Duration at 050 inch Lift: 221 int./225 exh.
Advertised Intake Duration: 275
Advertised Exhaust Duration: 279
Advertised Duration: 275 int./279 exh.
Intake Valve Lift with Factory Rocker Arm Ratio: 0.499
Exhaust Valve Lift with Factory Rocker Arm Ratio: 0.510
Valve Lift with Factory Rocker Arm Ratio: 0.499 int./0.510 exh. lift
Lobe Separation (degrees): 112
Intake Valve Lash (in): 0.000
Exhaust Valve Lash (in): 0.000
Computer Controlled: No
Grind Number: HR-224/339-2S-12
~Nick
 
The stage 1 TFS is no better than an E or the 2031 listed above.
What makes people think it's good i have no idea. Especially for a set of AFR's. There's a reason why the cam is $139 new.

And call comp and get a custom, not crane.

You may lose velocity with 185's on such a small engine.

Personally i think if you are hard up for money for the project, get wedges or edelbrock rpms and put the extra money towards an intake. There's not much justification for the xtra $300 afr's cost.