• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Injector/Computer Remapping Question

  • Thread starter Thread starter craZy400
  • Start date Start date Nov 1, 2005
C

craZy400

New Member
Jun 2, 2005
7
0
0
Nov 1, 2005
#1
  • Nov 1, 2005
  • #1
I just bought a complete "take off" fuel injection system from an '86 5.0 H.O. that I want to put on my '92 5.0 H.O. It has only seen the factory firing and no miles. Super clean and would be nice to start with a fresh set up.

Here is the catch. The fuel injectors are grey tops which means they are 14lbers. They only produce 140cc @ 3bars. Part number: E67E-B4B I found that these were only supposed to be on 4 and 6 cylinders so I am not sure how the heck they came on this set up. There are 8 of them and the rest of the fuel injection parts are 5.0 H.O. stuff.

My '92 injectors produce 194cc @ 3bars. Part number:E6TE-A2B

I assume this will cause a lean condition? Is there a way to remap the computer to compensate for the difference in cc's?

There are a few differences in the upper intake and the throttle body but I assume that is to reduce air flow or accomodate for the speed density system some how?

I know I could just go buy 19lbers and be done but I was hoping to use this set up since it practically brand new and I already spent the money. Plus I hope that this would give me an extra 1/2mpg

Thanks for any insight.
Ty Rogers
765.461.5048
 

donsbad68

Immensely Educated
Jan 4, 2003
838
0
0
Oklahoma
Nov 1, 2005
#2
  • Nov 1, 2005
  • #2
Your not going to like the answers your going to get on this.

DD
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Nov 1, 2005
#3
  • Nov 1, 2005
  • #3
If you have an adjustable fuel pressure regulator, you can turn up the fuel pressure to achieve a 19 lb flow.

According to the calculator I have, you need 70 PSI if the 14 lb rating was at 38 PSI. If the injectors were rated at 3 bar (44.1 PSI), you will need 83 PSI.
 
C

craZy400

New Member
Jun 2, 2005
7
0
0
Nov 2, 2005
#4
  • Nov 2, 2005
  • #4
Wouldn't I need a larger fuel pump to be able supply that regulator then? Sounds like a good way to increase leaking in the engine compartment :-(
 
C

craZy400

New Member
Jun 2, 2005
7
0
0
Nov 2, 2005
#5
  • Nov 2, 2005
  • #5
I might have an opprotunity to buy 19lbers but they are flow rated at 210cc @ 3bar which is over my stock 19lbers which are 194cc.

Wouldn't this cause a rich condition?

Or would the computer be able to compensate for it?

thanks again
Ty
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Nov 2, 2005
#6
  • Nov 2, 2005
  • #6
craZy400 said:
Wouldn't I need a larger fuel pump to be able supply that regulator then? Sounds like a good way to increase leaking in the engine compartment :-(
Click to expand...
In theory, it is still only 19 lbs per injector, so the pump size would remain the same. In practice, I problably would increase the pump size from 88 LPH (stock) to 112 LPH.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Nov 2, 2005
#7
  • Nov 2, 2005
  • #7
craZy400 said:
I might have an opprotunity to buy 19lbers but they are flow rated at 210cc @ 3bar which is over my stock 19lbers which are 194cc.

Wouldn't this cause a rich condition?

Or would the computer be able to compensate for it?

thanks again
Ty
Click to expand...
Stick with the Ford orange (old dirty ones look tan) injectors and you will have much less problems. The computer will trim the fuel flow at cruse by using the O2 sensors.
 
You must log in or register to reply here.

Similar threads

S
Fuel ‘88 GT Runs Rich Cold — Fixes Itself When I Unplug Sensors (ECT, MAF, O2, etc.)
  • Sufarry
  • Nov 6, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
1K
Fox 5.0 Mustang Tech Nov 9, 2025
Mustang5L5
Fox Fuel injection questions
  • limp
  • Jul 26, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
15
Views
608
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 19, 2026
AeroCoupe
S
Requesting Guidance for 306 motor swap - Fuel? - SD? MAF?
  • So_Flo
  • Jul 26, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
32
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 4, 2026
Mcmahst
Progress Thread Giving an abandoned 88 GT project a new chance at life
  • jaketractor
  • Jan 9, 2025
  • Fox 5.0 Mustang Tech
  • 2
Replies
27
Views
2K
Fox 5.0 Mustang Tech Jul 20, 2025
Noobz347
D
Computer support for top end mods?
  • Duramax6
  • Oct 11, 2023
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
24
Views
4K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 1, 2023
2000xp8
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?