Molding the fenders

1105 · Sep 12, 2004

I got finished today with hiding the wires and putting the car back together and I got out some cardboard and mocked up a template for me to use to mold my fenders smooth. I'm going to look around some places tomorrow to see if I can find any sheet metal that I'll be able to use. Heres a few pictures of what its going to look like. After I get done with the fenders, I'm going to move onto other parts of the engine bay that I can get to with the engine still in it, then finally pull it out to finish the rest of the body work and paint it. I'm probably going in over my head on this one

huskerpower02 · Sep 12, 2004

so whatever happend to your DIY turbo project

1slow95 · Sep 12, 2004

That looks really good so far. Nice job! Im gonna start on mine this winter when I swap in the 418. I know it's gonna be a big job, but I think Im ready for it. Keep us updated on your progress!

1105 · Sep 12, 2004

I'm going to be picking up the sheet metal tomorrow on my way to oinks house where we're going to make better templates... Might have the pieces cut out tomorrow and MAYBE tached in place. Bondo is going to soon be my best friend

1105 · Sep 12, 2004

huskerpower02 said:
so whatever happend to your DIY turbo project

twins are scrapped... too many problems with oil and exhaust pipes.. I'm waiting on some hotside parts for a new single turbo so I figured I'd start this while I'm waiting. This is the turbo I'm going to be running. Master Power T70 ball bearing 60.5mm

mustangmatt685 · Sep 13, 2004

I hate and love you all at the same time, I wish I could afford a turbo, but its all good becuase Id probably kill myself with it anyway. Good luck with molding the fenders, metal work is fun....

BlueOvalStangGT · Sep 13, 2004

i say just paint the cardboard.

rudeone707 · Sep 13, 2004

BlueOvalStangGT said:
i say just paint the cardboard.

just make youre you use the paint with the ceramic coating.

looks good man, cant wait to see it when your done.

1105 · Sep 13, 2004

I was actually going to spray it with left over paint from when I painted my car then clear coat it. This will be an ongoing project over months probably. Just something to keep me busy

GTJake · Sep 13, 2004

Damn, tuck those fuel lines under the TB/CAI.

Jake

donjohn · Sep 13, 2004

i like the loner blue wire

1105 · Sep 13, 2004

donjohn said:
i like the loner blue wire

Its not alone... theres another blue wire with it Two of my red ones got burnt

Hellbent66 · Sep 13, 2004

No ceramic paint needed! Base coat clear coat will be fine for the inner fenders. I spray it on engines all the time No problems at all with heat. Looks good keep posting pictures of the metal work!

1105 · Sep 13, 2004

Hellbent66 said:
No ceramic paint needed! Base coat clear coat will be fine for the inner fenders. I spray it on engines all the time No problems at all with heat. Looks good keep posting pictures of the metal work!

sure will. I picked up a 2' x 3' sheet of 22 gauge sheet metal and I'm going to start making better templates than that I have right now. Might try that tomorrow? If not I'm going to defently be working on it come this weekend.

OinkAodeOink · Sep 13, 2004

Hellbent66 said:
No ceramic paint needed! Base coat clear coat will be fine for the inner fenders. I spray it on engines all the time No problems at all with heat. Looks good keep posting pictures of the metal work!

You are right, but with a turbo setup, he'll need to watch the paint. Making sure to wrap the turbo up well, in heat insulation.

My turbine is about 10" from the body work, and i already have a hairline crack from the heat. Also my hood has blistered and peeled up, from the heat.. So be sure to cover that hotass turbo in a thick blanket!

OrangeMustangGt · Sep 13, 2004

woah the turbo gets a doiley

1105 · Sep 16, 2004

Today I got some a new template made for the drivers side. It SHOULD work on the pass side since it looks the same. I'm going to start cutting the sheet metal out in a little bit. Working outsite in near 100 degree weather isnt any fun Heres the pic's of the new template I made. Looks a lot nicer than the cardboard that I used before

gcomfx.com · Sep 16, 2004

Hellbent66 said:
No ceramic paint needed! Base coat clear coat will be fine for the inner fenders. I spray it on engines all the time No problems at all with heat. Looks good keep posting pictures of the metal work!

I think rudeone707 was joking about painting the cardboard with ceramic coating.

pleasehelp · Sep 17, 2004

1105 said:
twins are scrapped... too many problems with oil and exhaust pipes.. I'm waiting on some hotside parts for a new single turbo so I figured I'd start this while I'm waiting. This is the turbo I'm going to be running. Master Power T70 ball bearing 60.5mm

But now you're selling it?? http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&rd=1&item=2489963052&category=6755

DARK-5.0 · Sep 17, 2004

Good thinking with the fenders. I did the same thing back in march when the motor was out, but I went a different route and used fiberglass. If i could go back and do it again, which i will. I would use sheetmetal. Here are a few pics of mine

Good luck with the project.

Jeremy

Molding the fenders

1105

I AM the random post master...bow down

huskerpower02

Member

1slow95

1105

I AM the random post master...bow down

1105

I AM the random post master...bow down

mustangmatt685

New Member

BlueOvalStangGT

Active Member

rudeone707

New Member

1105

I AM the random post master...bow down

GTJake

donjohn

New Member

1105

I AM the random post master...bow down

Hellbent66

New Member

1105

I AM the random post master...bow down

OinkAodeOink

OrangeMustangGt

1105

I AM the random post master...bow down

gcomfx.com

pleasehelp

New Member

DARK-5.0

Similar threads

Molding the fenders

I AM the random post master...bow down

Member

I AM the random post master...bow down

I AM the random post master...bow down

New Member

Active Member

New Member

I AM the random post master...bow down

New Member

I AM the random post master...bow down

New Member

I AM the random post master...bow down

I AM the random post master...bow down

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency