• Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-

Need Advice On Project Mustang

  • Thread starter Thread starter RJ70
  • Start date Start date Jan 17, 2018
  • Tags Tags
    mustang need advice need help project car
R

RJ70

New Member
Jan 17, 2018
4
0
1
Jan 17, 2018
#1
  • Jan 17, 2018
  • #1
I just recently found a listing for a 1970 Mustang Coupe (I believe it's the coupe model) and I've always wanted to drive a classic muscle car, but it's in pretty rough shape. The author of the post said it runs but the interior is rusty and I assume the trunk is worse. This doesn't bother me though because my goal has always been to buy an older classic and fix it up so I can learn through the process.

The point is, they're asking $2500 for it and I don't know if that's a good deal or not for a project car (even if it is a mustang) because I've never really done this before.

Another thing I was curious about is if anyone here could give me a rough estimate of what it will take to fix it up to decent shape. It will need interior door panels, carpeting and flooring done (however that works), the front bumper is missing some of the accessories like the grill and lights and such, and there is a possibility I might have to weld some new panels on if the rust is bad enough. The paint job is just a flat black that looks fine for now but I'll probably redo later, and the engine is going to be a part by part replacement project so I'm not looking for estimates on that either.

I'm new to this so any advice you have is greatly appreciated. Thank you.
 

WORTH

20+ Year Stangneter
Nov 18, 2002
2,166
44
98
Cape Cod, Ma.
Jan 17, 2018
#2
  • Jan 17, 2018
  • #2
can't tell you a thing without Pix. Mustang coupes are everywhere and not real valuable, so condition is everything.
 
R

RJ70

New Member
Jan 17, 2018
4
0
1
Jan 17, 2018
#3
  • Jan 17, 2018
  • #3


These are the only three pictures that came with the original post. I asked them to take more and send them to me, so I'll post those when I get them.
 

WORTH

20+ Year Stangneter
Nov 18, 2002
2,166
44
98
Cape Cod, Ma.
Jan 18, 2018
#4
  • Jan 18, 2018
  • #4
well it's a 6 so that is the least valuable. So the deciding factor is how much rot. You need pix of the entire underneath. It's a unibody so it's not easy to fix, everything has to be cut out and welded in and has to remain perfectly straight while you are doing it. I always recommend to a noobe, if you want to restore a car, start with a car from the 40's, or a pickup up to the 50's. If you survive that, you will learn a lot on a simple restore and you can sell it and get what you want. Unibody's are a pain in the ass to work on.
 
R

RJ70

New Member
Jan 17, 2018
4
0
1
Jan 18, 2018
#5
  • Jan 18, 2018
  • #5
Thank you for your advice.
 

rbohm

Founding Member
Apr 12, 2002
6,698
550
204
tucson,az
Jan 19, 2018
#6
  • Jan 19, 2018
  • #6
the rust i see in the pictures seems to be surface rust, and thus not really a problem. i would however investigate further, tap the rust areas with a screwdriver with a bit of force, if the blade punches through then the panel needs replacing, and not really a job for a novice, depending on how bad the rust is. if you can cut and weld, that makes things easier though.

the six can be made to make some decent power while maintaining decent fuel economy, so if you decide to get the car, and want to keep the six, let me know, i can help or point you in the right direction. it does look like it has the 250 though, and that is good actually.

i dont think this car is worth $2500, $1500-1800 is more like it imo. if you buy this car though, have a plan for what you want this car to be before turning wrench one. i would also make sure that you have all the parts before buying the car as well.
 
R

RJ70

New Member
Jan 17, 2018
4
0
1
Jan 24, 2018
#7
  • Jan 24, 2018
  • #7
@rbohm thank you for your advice as well. Unfortunately the car sold before I had a chance to actually go look at it or make an offer but your advice was still very appreciated regardless. If I have questions in the future about something like this, I'll be sure to let you know.
 

rbohm

Founding Member
Apr 12, 2002
6,698
550
204
tucson,az
Jan 24, 2018
#8
  • Jan 24, 2018
  • #8
be my guest.
 
You must log in or register to reply here.

Similar threads

C
Need 1973 Mustang schematic
  • Cudajim
  • Sep 28, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
18
Views
495
1965 - 1973 Classic Mustangs -General/Talk- Oct 10, 2025
manicmechanic007
M
Inheriting (and likely restoration of) a 1965 Mustang
  • miniwheats235
  • Feb 17, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
2
Views
234
1965 - 1973 Classic Mustangs -General/Talk- Feb 19, 2026
Realmongo
O
Help
  • OnisimusD
  • Oct 13, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
16
Views
386
1965 - 1973 Classic Mustangs -General/Talk- Oct 14, 2025
OnisimusD
O
D
96 get convertible-sell or part out?
  • DTCstang
  • May 17, 2026
  • What is it Worth?!?!?
Replies
5
Views
103
What is it Worth?!?!? May 18, 2026
nickyb
Classic Car Insurance
  • Willybill32
  • Feb 24, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 3 4 5
Replies
83
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 3, 2026
7-UP BILL
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?