• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Fox New Here: Saying Hello With Questions

  • Thread starter Thread starter polaraman
  • Start date Start date Feb 27, 2015
Prev
  • 1
  • 2
First Prev 2 of 2

polaraman

Member
Feb 27, 2015
46
15
18
Dublin, GA
Mar 9, 2015
#21
  • Mar 9, 2015
  • #21
Here... This is the nipple I need to get to...
 

Attachments

  • 1425930517470.webp
    61.3 KB · Views: 173

polaraman

Member
Feb 27, 2015
46
15
18
Dublin, GA
Mar 9, 2015
#22
  • Mar 9, 2015
  • #22
It's tucked back deep under this...
 

Attachments

  • 1425930725162.webp
    77 KB · Views: 159

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Mar 9, 2015
#23
  • Mar 9, 2015
  • #23
Remove the upper intake manifold - 6 bolts, 2 of which are hidden under the 5.0 cover plate. Then you get to pop off the throttle cable, inlet air duct and some other miscellaneous hoses and electric connections to get the upper intake manifold off.

Seriously, it is time for a Chilton's shop manual...Buy one before you break something expensive.

 

Attachments

  • 5.0 FORD INTAKE MANIFOLD EXPLODED VIEW.gif
    118.9 KB · Views: 374
Reactions: polaraman

polaraman

Member
Feb 27, 2015
46
15
18
Dublin, GA
Mar 9, 2015
#24
  • Mar 9, 2015
  • #24
You are absolutely right. I'm relying on my limited mechanical skill to work on a car I'm not familiar with. This is my first 5.0. I've had a half dozen SBCs.

I'll order one tonight.
 
Reactions: Shoomakan

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Mar 9, 2015
#25
  • Mar 9, 2015
  • #25
I like to hear success stories and not tales of woe. The manual is a good first step...
 

polaraman

Member
Feb 27, 2015
46
15
18
Dublin, GA
Mar 12, 2015
#26
  • Mar 12, 2015
  • #26
jrichker said:
I like to hear success stories and not tales of woe. The manual is a good first step...
Click to expand...

I need to update everyone. Chilton manual ordered. Should be in by this weekend.

I was able to swap out that vacuum line under the intake without taking it off. It was a very tight fit but I got my hand up in there. My surging idle is fixed!!! Thanks to everyone for their help.

However, I've encountered another issue. I've driven the car all week with no issues until today. I drove it home from work and had to run back out. When I tried to crank, it was flooded. I waited about 10 minutes and tried it again. It ran for about three minutes and flooded again.

What would cause the engine to flood like that? I can smell the gas it's not burning. It's a very strong smell.
 

90lxwhite

I'm kind of a She-Man
5 Year Member
Aug 25, 2011
3,310
374
134
Between the Red and Rio
Mar 12, 2015
#27
  • Mar 12, 2015
  • #27
polaraman said:
I need to update everyone. Chilton manual ordered. Should be in by this weekend.

I was able to swap out that vacuum line under the intake without taking it off. It was a very tight fit but I got my hand up in there. My surging idle is fixed!!! Thanks to everyone for their help.

However, I've encountered another issue. I've driven the car all week with no issues until today. I drove it home from work and had to run back out. When I tried to crank, it was flooded. I waited about 10 minutes and tried it again. It ran for about three minutes and flooded again.

What would cause the engine to flood like that? I can smell the gas it's not burning. It's a very strong smell.
Click to expand...
Fuel pressure regulator??
 

TOOLOW91

If you're the village idiot what's that make me?
20+ Year Stangneter
Nov 29, 1999
8,483
8,687
234
S.I.NY
Mar 12, 2015
#28
  • Mar 12, 2015
  • #28
Pull vac like off the fuel pressure reg if there is fuel coming out its 100 percent no good


Sent from my iPhone using my fingers while my auto correct makes me seem illiterate
 
Reactions: jrichker

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Mar 12, 2015
#29
  • Mar 12, 2015
  • #29
EFI strategy to clear a flooded engine: Hold the accelerator to the floor and crank the engine. When it starts, quickly let off the throttle.

Fix: follow TOOLOW91's suggestion to check the vacuum line on the fuel pressure regulator.
If you don't find or smell fuel, then dump the codes and look for ECT codes 21, 51 or 61.


Dump the codes: Codes may be present even if the Check Engine Light (CEL) isn't on.

Dumping the computer diagnostic codes on 86-95 Mustangs

Revised 26-July-2011. Added need to make sure the clutch is pressed when dumping codes.

Codes may be present even if the check engine light hasn’t come on, so be sure to check for them.

Here's the way to dump the computer codes with only a jumper wire or paper clip and the check engine light, or test light or voltmeter. I’ve used it for years, and it works great. You watch the flashing test lamp or Check Engine Light and count the flashes.

Post the codes you get and I will post 86-93 model 5.0 Mustang specific code definitions and fixes. I do not have a complete listing for 94-95 model 5.0 Mustangs at this time.

Be sure to turn off the A/C, and put the transmission in neutral when dumping the codes. On a manual transmission car, be sure to press the clutch to the floor.
Fail to do this and you will generate a code 67 and not be able to dump the Engine Running codes.





If your car is an 86-88 stang, you'll have to use the test lamp or voltmeter method. There is no functional check engine light on the 86-88's except possibly the Cali Mass Air cars.



The STI has a gray connector shell and a white/red wire. It comes from the same bundle of wires as the self test connector.

89 through 95 cars have a working Check Engine light. Watch it instead of using a test lamp.



The STI has a gray connector shell and a white/red wire. It comes from the same bundle of wires as the self test connector.


WARNING!!! There is a single dark brown connector with a black/orange wire. It is the 12 volt power to the under the hood light. Do not jumper it to the computer test connector. If you do, you will damage the computer.

What to expect:
You should get a code 11 (two single flashes in succession). This says that the computer's internal workings are OK, and that the wiring to put the computer into diagnostic mode is good. No code 11 and you have some wiring problems. This is crucial: the same wire that provides the ground to dump the codes provides signal ground for the TPS, EGR, ACT and Map/Baro sensors. If it fails, you will have poor performance, economy and driveablity problems

Some codes have different answers if the engine is running from the answers that it has when the engine isn't running. It helps a lot to know if you had the engine running when you ran the test.

Dumping the Engine Running codes: The procedure is the same, you start the engine with the test jumper in place. Be sure the A/C is off, and clutch (if present) is pressed to the floor, and the transmission is in neutral. You'll get an 11, then a 4 and the engine will speed up to do the EGR test. After the engine speed decreases back to idle, it will dump the engine running codes.

Trouble codes are either 2 digit or 3 digit, there are no cars that use both 2 digit codes and 3 digit codes.

Your 86-88 5.0 won't have a working Check Engine Light, so you'll need a test light.
See AutoZone Part Number: 25886 , $10




Alternate methods:
For those who are intimidated by all the wires & connections, see Actron® for what a typical hand scanner looks like. Normal retail price is about $30 or so at AutoZone or Wal-Mart.

Or for a nicer scanner see Equus Digital Ford Code Reader (3145) Equus - Digital Ford Code Reader (3145It has a 3 digit LCD display so that you don’t have to count flashes or beeps.. Cost is $22-$36.
 
Reactions: TOOLOW91

90lxwhite

I'm kind of a She-Man
5 Year Member
Aug 25, 2011
3,310
374
134
Between the Red and Rio
Mar 13, 2015
#30
  • Mar 13, 2015
  • #30
90lxwhite said:
Fuel pressure regulator??
Click to expand...
TOOLOW91 said:
Pull vac like off the fuel pressure reg if there is fuel coming out its 100 percent no good


Sent from my iPhone using my fingers while my auto correct makes me seem illiterate
Click to expand...
Good answer. Wish I would've thought of that.
 
Prev
  • 1
  • 2
First Prev 2 of 2
You must log in or register to reply here.

Similar threads

S
idles perfect then jolts and cuts out when put into Reverse or Drive.
  • shanesstangs
  • Mar 12, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
234
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 27, 2026
General karthief
Mustang II 4 cyl gear hunting and possibly messed up vacuum system
  • oesterreicher
  • May 31, 2026
  • 1974 - 1978 Mustang II Talk & Tech
Replies
11
Views
289
1974 - 1978 Mustang II Talk & Tech Jun 14, 2026
manicmechanic007
G
1991 GT 5.0 running hot
  • gvanginkel403
  • Jul 1, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
141
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 2, 2026
General karthief
S
Drivetrain Downshifting from 3rd to 2nd issue
  • Scott_S
  • Apr 23, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
754
Fox 5.0 Mustang Tech Jun 14, 2026
Mindseye007
5
Hello Everyone !
  • 5150K
  • Jul 3, 2026
  • The Welcome Wagon
Replies
0
Views
77
The Welcome Wagon Jul 3, 2026
5150K
5
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?