over carburated??/

saleen91

New Member
Feb 4, 2006
3
0
1
el paso tx
hi i need some help from anyone willing to help me, heres what i have , 93 coupe with a carburated 302, b cam (flat tappet), stealth intake, holley red fuel pump, 750 speed demon, 150 shot nitrous, aod with shift kit and 3500 stall, 3 73 gears . my problem is that when ever i drive it for a while it cut off completely, i have to press the gas all the way down for it to start and keep pressing it so that it wont die out. I emailed summit tech and they said i was overcarburated, i then told them i had an edelbrock 650 carb and it did the same thing. the guy said i should go with a 600 carb, but if i do would it affect everything else i am going to put on? i am going to put on a stage 2 trickflow cam (hydrolic) new lifters, aftermarket heads and rockers, i think that 600 would be too small i dont know i am at a total loss theres going to be a shoot out in april and i wanna be there not to watch but to race can anyone outhere help me!!!!!!!!!!!!!!!!!!!:scratch:
 
even if thats more carb than you need it shouldn't run crappy like that if it's tuned half way decent. you said it did the same thing with the smaller carb.

make sure your fuel pump isn't over powering your needle seat assembly and flooding the carb. ok you said a red fuel pump, whats the psi rating on that?? seems like their supposed to be rated at 6 or 7 psi but might wanna check it anyway. have you checked the float level??

holley type carbs need to have a functioning and properly sized powervalve as well, especially if you have a lopey cam with not alor of idle vaccum.

there's lots of things i could point to on that carb but that doesnt explain why it runs that way with the other carb........it shouldn't do the same thing with 2 totally different carbs..might wanna re check your timing too.....especially if your using a vac advance distributor. does it do this at cruise or just at idle??

as for the carb sizing........you don't need a 750 but it should certainly run better than it is now.....if it's a vaccum secondary carb it wont give the engine more than it can handle, and sometimes cars with cams like slightly bigger primaries at idle anyway...now theres gonna be those that say that carbs too big......we could debate that all day but regardless it should not have those kind of drivability issues if it's adjusted right. like i said i'd blame it on that 750 but it's doing it with the smaller one as well, so somthin else is up.........unless both carbs just happen to be screwed up.......

the edelbrock 600/650 either one should work fine if it's working right.......is that an afb style or the newer thunder series avs one?? i think the 650's are all the thunder series....not sure why summit would recomend a 600 when you have a 650:shrug:
 
Almost sounds like its flodding the motor while your diving. Since you said you have to hold the throttle down all the way to get it to start again. I would Def. go with a 600. And I would go with an edelbrock. I tried a couple Holley and they never ended up completely right. The edelbrock will start right up and minimal tuning. IMO great for daily driving as well.
 
I would say it is overcarburated with a 750 but that isnt your problem here. I would start with the basics and check to make sure there is no debris in the needle valves and make sure they are adjusted right. You are running a decent fuel filter right? If not, get one. Any little piece of crap in the gas will stick one of those valves open and literaly dump gas in your motor. And if you do decide to get a new carb...The Edelbrocks are great for daily drivers that you dont want to fiddle with all the time but not nearly as tunable as a Holly or clone. I have found the Edelbrocks tend to be fairly close out of the box and you can pretty much bolt it on and go in most cases, they seem to be somewhat self adjusting to a point where as the Holly will definately require some tuning to make it run right. I'm a Holley fan though so thats what I would go with.
 
On my new project, I am running a 1406 Edelbrock with a electric choke, and I am going to see how it goes before going to a bigger carb. I am running a 351 bored .40 over with TFW heads and a stage 1 TFW cam. I have KB's pistons and a Edelbrok RPM intake.

Though the edelbrocks are not as tuneable as a holley or speed demon, they do work well, and its a no fuss no muss deal with them once they are tuned. realibility is a factor when you are building your mortor as well.

Have someone tune your carb/engine, and go with the 650.
 
it does this when i am cruisin it , i havent even tried to race it havent even filled the bottle , there is a possibility that both carbs are screwed but the guy said he had just bought and installed it :bang:
timewarped1972 said:
even if thats more carb than you need it shouldn't run crappy like that if it's tuned half way decent. you said it did the same thing with the smaller carb.

make sure your fuel pump isn't over powering your needle seat assembly and flooding the carb. ok you said a red fuel pump, whats the psi rating on that?? seems like their supposed to be rated at 6 or 7 psi but might wanna check it anyway. have you checked the float level??

holley type carbs need to have a functioning and properly sized powervalve as well, especially if you have a lopey cam with not alor of idle vaccum.

there's lots of things i could point to on that carb but that doesnt explain why it runs that way with the other carb........it shouldn't do the same thing with 2 totally different carbs..might wanna re check your timing too.....especially if your using a vac advance distributor. does it do this at cruise or just at idle??

as for the carb sizing........you don't need a 750 but it should certainly run better than it is now.....if it's a vaccum secondary carb it wont give the engine more than it can handle, and sometimes cars with cams like slightly bigger primaries at idle anyway...now theres gonna be those that say that carbs too big......we could debate that all day but regardless it should not have those kind of drivability issues if it's adjusted right. like i said i'd blame it on that 750 but it's doing it with the smaller one as well, so somthin else is up.........unless both carbs just happen to be screwed up.......

the edelbrock 600/650 either one should work fine if it's working right.......is that an afb style or the newer thunder series avs one?? i think the 650's are all the thunder series....not sure why summit would recomend a 600 when you have a 650:shrug:
 
still sounds like somthing might be flooding the carb out.......

TRY THIS- run the car for a minute.......shut it off. usually you check float level with the engine running but at this point no need to have it running because your just seeing if the float bowls are being flooded. you have two float site plugs on the carb ( holley style) one on the side of each float bowl. some carbs have clear sight plugs so you can see the gas sloshing when you rock the car and tell if the level is right, although if your float bowls are overly flooded you might not be able to tell by looking at them anyway. if they arent the clear view sight plugs, remove the sight plugs......( plugs on the SIDE of the float bowls, NOT the screw and nutt on top) if gas comes gushing out, your float level is too high or your fuel pump is over powering the needle seat assembly inside over filling the float bowl.......start from there and see what happens.......ultimately you want the gas level in the bowl to be at about the bottom of the sight plug threads, if it just comes pouring out, it's too full......
 
a 650 is the most I'd go with your combo...also, don't forget to get the one with the Ford kickdown linkage for that AOD.

Possibly when you're cruising for a while, and the AOD needs to downshift it's not, so the carb is flooding because you're pushing on the pedal too much and the car's dogging? :shrug:

just throwing an idea out...
 
timewarped1972 said:
i missed he had an aod.......good point.....making sure that tv cable is right....
you know what as a matter a fact thats another thing, my car wont shift into next gear until red line, thats why i dont like running it to much i dont want to mess anything up my aod has a shift kit and a 3500 stall :shrug: