Fox Shaving engine bay, hood release?

Kid wita 5oh · Jan 29, 2024

I'm in process of doing the scott rod fab panels and painting my engine bay, I'm trying to hide as much as possible. (Wiring etc..)

I'm also trying to hide the hood release cable, right now I have the body harness and hood cable coming through where the cruise stuff would in the driver's fender. The cable is about 3-4" too short...

Does anyone have a pathway that it will reach, or know of a longer cable that will work?

It's a stock hood and latch, and it will stay that way, hood pins or other latches aren't an option

bird_dog0347 · Jan 29, 2024

Kid wita 5oh said:
Does anyone have a pathway that it will reach, or know of a longer cable that will work?

It's a stock hood and latch, and it will stay that way, hood pins or other latches aren't an option

I don't know about the cable length or routing, but as for hood pins if you're using a fiberglass hood I would SERIOUSLY reconsider and get some pins/latches. If it's a stock hood you'll be ok but otherwise do yourself a favor and get the insurance of pins.

Kid wita 5oh · Jan 29, 2024

Kid wita 5oh said:
It's a stock hood and latch, and it will stay that way, hood pins or other latches aren't an option

Mustang5L5 · Jan 29, 2024

I only partially shaved my engine bay and did a partial wire tuck. I am pretty sure i had the cable come out of the iriginal hole and then immediately routed it into the fender, but I will need to check. From there i ran it along the outside of the upper rail. You can kinda see it in this pic. I'll have to go doube check what hole it came through the firewall. I still have cruise so I doubt i used that hole for the cable.

bird_dog0347 · Jan 29, 2024

May bad, I typed that before my coffee...

ebone84 · Jan 29, 2024

I’m looking at your vacuum tree....... wish I would’ve moved mine years ago ...... i’m going to relocate my radio ...... and just drive .......

TOOLOW91 · Jan 30, 2024

Mustang5L5 said:
I only partially shaved my engine bay and did a partial wire tuck. I am pretty sure i had the cable come out of the iriginal hole and then immediately routed it into the fender, but I will need to check. From there i ran it along the outside of the upper rail. You can kinda see it in this pic. I'll have to go doube check what hole it came through the firewall. I still have cruise so I doubt i used that hole for the cable.

Exactly this . Something is off with his routing . I’ve done 2-3 like that and no issue

Mustang5L5 · Jan 30, 2024

Double checked my routing.

Original hole right into one of the holes on back of strut tower. Front there I route as shown above.

Kid wita 5oh · Jan 31, 2024

I'm definitely not in the original hole, and want to try to keep it out of the bay completely.

I'll recheck under the dash to see if Im looped around a harness or something. If you guys are able to reach the latch making the turn into the strut tower I should have plenty the way I am doing it

Kid wita 5oh · Jan 31, 2024

@Mustang5L5 do you have more pics of how you routed your vacuum lines?

AeroCoupe · Jan 31, 2024

@Noobz347..."I'm definitely not in the original hole"??? Come on man you have to do it.

Mustang5L5 · Jan 31, 2024

Kid wita 5oh said:
@Mustang5L5 do you have more pics of how you routed your vacuum lines?

I searched for a good 10 mins but don't have any good pics unfortunately.

All i have is a sorta-pic showing it here. Essentially the main line from the intake connects to Source (on the left) and comes in from a hole on the rear of the strut tower. I have hydroboost so I don't need to feed the brake booster. My cruise just gets a small jumper to the module, but I run the AC line through the cowl.

The line with the red arrow goes through the cowl over to the other side where I feed the HVAC stuff behind the strut tower.

I looked for better pics but guess i didn't take any. Everything under the fenders now

Noobz347 · Jan 31, 2024

Now, he's in a whole different hole altogether.

AeroCoupe · Jan 31, 2024

I see what you did there…

Kid wita 5oh · Feb 1, 2024

I just noticed my new profile quote or what ever you call it. That's awesome hahah

General karthief · Feb 1, 2024

Kid wita 5oh said:
I just noticed my new profile quote or what ever you call it. That's awesome hahah

Congratulations
That's a CT, means you're SPECIAL! (he says in his best Dana Carvey voice)

Mustang5L5 · Feb 6, 2024

Found better pics

Prob could have hid this stuff better but wasn’t going for a total tuck. Still wanted to be able to service some stuff

Kid wita 5oh · Feb 6, 2024

Awesome thanks

Kid wita 5oh · Feb 20, 2024

Bay is painted, didn't go full crazy will filling holes but it's definitely way nicer now. Figured I'd throw some pics here rather than start a new thread.
Assembly coming soon

Kid wita 5oh · Feb 20, 2024

.

Fox Shaving engine bay, hood release?

I'm definitely not in the original hole

still married haven't seen testicles in years

I'm definitely not in the original hole

That is…until I whipped out my Bissell

still married haven't seen testicles in years

If you're the village idiot what's that make me?

That is…until I whipped out my Bissell

I'm definitely not in the original hole

I'm definitely not in the original hole

lube between the nut and the face. I know my lubes

​

That is…until I whipped out my Bissell

Stangnet Facilities Maint Tech... Er... Janitor

lube between the nut and the face. I know my lubes

I'm definitely not in the original hole

wonder how much it would cost to ship you a pair

That is…until I whipped out my Bissell

I'm definitely not in the original hole

I'm definitely not in the original hole

I'm definitely not in the original hole

Similar threads

Privacy & Transparency

Privacy & Transparency