T5 transmission problem PLEASE

fiveoho · Mar 18, 2007

T5 transmission problem PLEASE HELP

i noticed a very simliar recent thread on this but wanted to post mine bc i did not want to hi jack theirs...

a friend and i just done a t-5 swap on my 95 with a t-5 from a 95 cobra. we took everything out down to the flyweel. i had the flywheel that came from the cobra resurfaced. the clutch is a centerforce and only had about 12k on it. we replaced everything and installed the 32k cobra t5 and went for a test drive. vibration is horrible. its very noticeable at crusing speeds. the clutch engages fine and the trans shifts ok ( noisy tho...or about the same amount of noise my 110k gt trans made ) but no grinds. there was no vibration before with my stock t5.

a few people have mentioned that my driveshaft is out of balace....but how could that be if it did not vibrate before? could the splines not be lined up the same? does that make a difference? is there a wrong way the input shaft goes into the motor? am i doing damage? im afraid to drive it. could exhaust rubbing the driveshaft cause that much vibration?

another thing someone mentioned was the input shaft bearing....could that be a problem on a 32k trans?

PLEASE HELP

urban96 · Mar 18, 2007

did you replace the pilot bearing? did you mark the D/S before you removed it so it would be installed the same way?

fiveoho · Mar 18, 2007

urban96 said:
did you replace the pilot bearing? did you mark the D/S before you removed it so it would be installed the same way?

did not replace the pilot bearing. we did mark the ds but tonight we are making sure we marked the ds right.

droptopford 5 0 · Mar 18, 2007

is it rpm or speed related?

95mustang_gt · Mar 18, 2007

Recheck all the bolts.I had a vibration when i got done with my swap.I took it to work and put it on the lift and the tranny to bellhousing bolts back out.I tighted them up,this time with air, and the car has no more vibrations.

fiveoho · Mar 19, 2007

seems to be more rpm related.

we looked at it tonight. we marked the driveshaft b4 we took it out but still did not put it back in with the marks.....in a hurry i guess. we aligned it and took it down the road. its better. still some vibration tho. you can sit still and rev it and u can feel it. i guess now its exhaust? when we bolted the exhaust back on after the trans swap, it didnt really go back together so smooth and is hanging in different places than before.

another thing-

when the clutch is in and i am feathering the throttle to take off something whistles. the best way i can describe it is kinda like a charger. it sounds cool but i dont like it bc i dont know what it is. not 100% sure but i think it only does it when the clutch is mashed in and throttle is applied.

thanks guys

fiveoho · Mar 19, 2007

i will recheck all my bolts too on everything

Adam95GT · Mar 19, 2007

good you found the problem... the ds can be trickey... im glad to hear everything turned out good... im not sure what the noise could be maybe an exhaust leak??? ... just hope its not the trans its self.... the vibration might also be the harmonic balancer.... was it there at all b4 the swap???

fiveoho · Mar 19, 2007

thanks adam

no- there was no vibration at all b4. when we repositioned the ds, that helped alot. i really think and hope exhaust is the main problem now.
what inside the trans would whistle?..........or were u just meaning something else causing the whistling?

also, this 32k cobra t5 is not any quieter than my 110k gt t5. it goes into gear perfect, no grinds....just noisy. are the cobra t5's any noiser or is this just the nature of a manual trans? several ppl have told me ( even a trans guy ) that manual trans' WILL make some noise just bc its metal against metal

is the nature of a t5 just a little noisy?

note: i also have a steeda tri ax.....could the aluminum shifter be transferring some noise?

btw: adam, glad to hear about your motor/tranny purchase. hope all works out well for you. i know you had quite a few miles on your last.

Adam95GT · Mar 19, 2007

thanks man... yea t-5s can be quite noisy some do whine when in gear alot... it could be a small exhaust leak too you never know... my t-5 whines in 3rd gear... but it also grinds some times...

fiveoho · Mar 19, 2007

if i get the vibration out i will be happier.

not thrilled about the racket the trans makes but maybe im too anal?

fiveoho · Mar 19, 2007

got the exhaust re positioned and tightened down. almost all vibration is out.

now....whats that darn whistle when the clutch is engaged and the throttle is feathered??!!!

wytstang · Mar 20, 2007

The shifter does increase noise (mainly a whining noise), normaly all the gears except 4th are noise. As far as the whistle that hard to find,by any chance are you running a bbk tb? those are known for whistling while they work.

wytstang · Mar 20, 2007

Also the vibration can be as simple as your U joints going bad.

fiveoho · Mar 20, 2007

thanks wytstang. i appreciate the help. my u joints were replaced about 1.5 year ago ....i think. that would be something fairly inexpensive and easy to do if the vib is still there.

as far as my tri ax, that will transfer more noise?- that makes me feel better. 4th not making noise....is that because its 1:1, or something like that? my 4th you can still hear some whine but like i said, maybe im just too anal

if the car is sitting still running with the clutch not engaged and in neutral, the gears inside the tranny are turning correct ? with the clutch engaged and in gear, no gears are turning?

so when downshifting to like 3rd at say 2500, you will hear some whine and thats ok? going thru the gears, you will hear some whine? other than whine the other noise i hear is hard to explain. just sounds like gears meshing i guess, no grinding sounds just metallic contact ?

as for the throttle body, no BBK here. is the whistle something that you would worry about? i did not do it until after we swapped flywheels, bells, trannys

thanks

Green 94 5.0 · Mar 20, 2007

if it is rpm related and it does it in neutral, you can eliminate the tranny, driveshaft, and clutch from being any part of the problem. my guess would be the flywheel.

fiveoho · Mar 20, 2007

Green 94 5.0 said:
if it is rpm related and it does it in neutral, you can eliminate the tranny, driveshaft, and clutch from being any part of the problem. my guess would be the flywheel.

Just got it resurfaced before i installed it

wytstang · Mar 20, 2007

The tri ax (and all others) will transfer noise, 4th still make noise just not as loud just a faint whine to it. It could be the 1:1 as that was my gues as well. And yes downshifting will creat the whine/noise, also no gears are moving while idling and in neutral (that I'm aware of).

fiveoho · Mar 21, 2007

maybe it just makes noise and is ok

fiveoho · Mar 28, 2007

Green 94 5.0 said:
if it is rpm related and it does it in neutral, you can eliminate the tranny, driveshaft, and clutch from being any part of the problem. my guess would be the flywheel.

vibrates while going down the road ( rpm related ) and also vibtrates while sitting still ( also rpm related ) with the clutch depressed in or with it just in neutral.

still think it may be the flywheel with the vibration happening while the clutch is in or out?

-note: ordered a new FMS oem 50oz flywheel with bolt and dowel kit from summit. should be here tomorrow.

T5 transmission problem PLEASE

fiveoho

urban96

bubb rubb says:"woo woooooo"

fiveoho

droptopford 5 0

Member

95mustang_gt

New Member

fiveoho

fiveoho

Adam95GT

New Member

fiveoho

Adam95GT

New Member

fiveoho

fiveoho

wytstang

Mustang Master

wytstang

Mustang Master

fiveoho

Green 94 5.0

fiveoho

wytstang

Mustang Master

fiveoho

fiveoho

Similar threads

T5 transmission problem PLEASE

bubb rubb says:"woo woooooo"

Member

New Member

New Member

New Member

Mustang Master

Mustang Master

Mustang Master

Similar threads

Privacy & Transparency

Privacy & Transparency