• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

The Motor Is Out!

  • Thread starter Thread starter HotRodBlack
  • Start date Start date May 9, 2017
  • 1
  • 2
Next
1 of 2 Next Last

HotRodBlack

Active Member
Apr 24, 2017
31
15
28
May 9, 2017
#1
  • May 9, 2017
  • #1
Engine was making noise, it was driving me nuts pretending it was ok.

Pulled it out, wanna tear it apart and see what it is.

Common problems with high mileage 302 ho motors? Aaaaand go.

Also wish me luck!
 

Davedacarpainter

Chicks can make things hard if they’re inspired...
SN Certified Technician
Nov 28, 2015
11,833
11,634
203
Discordia
May 9, 2017
#2
  • May 9, 2017
  • #2
They're worn out?

Most I can offer without a better description of the sounds it was making.

You say you already have it pulled? What're your plans?

If you already have it pulled, you might as well......tear it down, put in new bearings,seals, timing gear set, hi volume oil pump, better flowing heads, custom cam, stroker forged crank(Callie's), forged rods and pistons, anything that says ARP, dart block, turbo, jack stands,supercharger, etc....etc....

Give us a couple details or do the above list.

I'm thinking you could have discovered what the problem was without pulling it simply by checking codes or asking us what we thought. I think you pulled the engine because you want to build it back yourself. That's good though. It's fun and rewarding to do an engine tear down and rebuild and have it run again because you did the work.

Seriously, tell us about the problems first. Our engines will have all sorts of problems depending on how they were treated.
 

HotRodBlack

Active Member
Apr 24, 2017
31
15
28
May 9, 2017
#3
  • May 9, 2017
  • #3
I actually had a post before with two videos of the noise... very little input from anyone...

Perhaps I was not direct enough in my questions. Idk.

The plans for the engine are just to get it repaired and put back in the car. I am not gonna go nuts with this engine as I don't have the money for a stronger transmission, so I'm not gonna push over 300 hp. Im gonna tear it down and measure everything and make sure it's viable. You know, check cylinder walls for scoring or loss of cross hatch pattern. I'll check all my bearing clearances and determine what it's gonna need. As of right now I'm 85 percent certain I will need main bearings, as there is too much crankshaft play, so those thrust bearings are poop. Tearing it down will tell me if the crank is viable or not, and if I need pistons and whatnot.

Currently this engine has an edlebrock intake, a set of bbl headers and h pipe hooked up to some warlock mufflers with dumps. Crane rocker arms (i can see through the oil fill) and a mild cam. I do not know what manufacturer the cam is. It's got a Bbk cold air kit on a stock t body and stock injectors. If anything, gt40 heads and a 65 mm tb plus 25lb injectors and mass air meter to match... but that's as far as this needs to go for now. Just a hot street set up.
 

HotRodBlack

Active Member
Apr 24, 2017
31
15
28
May 9, 2017
#4
  • May 9, 2017
  • #4
View: https://youtu.be/HMtkHLCbkAY


View: https://youtu.be/ZKNuDI1Fcrk
 

Davedacarpainter

Chicks can make things hard if they’re inspired...
SN Certified Technician
Nov 28, 2015
11,833
11,634
203
Discordia
May 9, 2017
#5
  • May 9, 2017
  • #5
I've probably even read your previous posts and have misplace them in my brain. Sorry dude, not meaning to be disrespectful, my life is full at the moment.

I think I remember a post or two by you. It would help to connect that memory if you might post a link or two.

Honestly, if I remember correctly, it could be something as simple as a loose valve train. Valve seals wear out, rockers need adjusting, etc...
 

CarMichael Angelo

my rearend will smell so minty fresh,
15 Year Member
Nov 29, 1999
10,641
8,909
234
Birmingham, al
May 9, 2017
#6
  • May 9, 2017
  • #6
Hmmm...hear a bad header leak,..maybe solid lifter cam....wouldn't have pulled the engine just yet.
 
Reactions: Davedacarpainter

Davedacarpainter

Chicks can make things hard if they’re inspired...
SN Certified Technician
Nov 28, 2015
11,833
11,634
203
Discordia
May 9, 2017
#7
  • May 9, 2017
  • #7
Funny that you posted that at the same time I was posting.

You do have a couple issues there. Let's get a mechanic involved, @90sickfox . Scott, help! And of course @madmike1157 .
 

HotRodBlack

Active Member
Apr 24, 2017
31
15
28
May 9, 2017
#8
  • May 9, 2017
  • #8
lol. I'm a pro technician myself
 
Reactions: Davedacarpainter

HotRodBlack

Active Member
Apr 24, 2017
31
15
28
May 9, 2017
#9
  • May 9, 2017
  • #9
Anywho. Not meaning to double post here, but I will post pics and info as the tear down commences. It might be a few days as I have to spend my days fixing other people's cars
 
Reactions: RaggedGT and Davedacarpainter

5.0Droptop

...all those nights we shared, and you're a dude??
Special Agent Mukity-Muck Whats in Charge Round Here
May 15, 2002
1,785
1,130
233
Indiana
May 10, 2017
#10
  • May 10, 2017
  • #10
HotRodBlack said:
Engine was making noise, it was driving me nuts pretending it was ok.

Pulled it out, wanna tear it apart and see what it is.

Common problems with high mileage 302 ho motors? Aaaaand go.

Also wish me luck!
Click to expand...

HotRodBlack said:
lol. I'm a pro technician myself
Click to expand...


 
Reactions: Davedacarpainter

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,133
10,749
213
polk county florida
May 10, 2017
#11
  • May 10, 2017
  • #11
You will soon be dreaming of mo powa
It starts with a simple 'fresh'n up' then 'well maybe I'll up grade this' and 'a better that' next thing you know you'll be sleeping in the garage, eating baloney sandwiches and drinking PBR so you can buy that turbo because those black marks in front of your house just aren't long enought.
 
Reactions: QuietOne, krazedstang, Nutty 5.o and 4 others

HotRodBlack

Active Member
Apr 24, 2017
31
15
28
May 10, 2017
#12
  • May 10, 2017
  • #12
karthief said:
You will soon be dreaming of mo powa
It starts with a simple 'fresh'n up' then 'well maybe I'll up grade this' and 'a better that' next thing you know you'll be sleeping in the garage, eating baloney sandwiches and drinking PBR so you can buy that turbo because those black marks in front of your house just aren't long enought.
Click to expand...

I'm sure you're right... but my budget will not allow it right now
 
Reactions: General karthief

FoxMustangLvr

I love my Pimp
SN Certified Technician
Oct 14, 2012
4,968
3,514
204
Spokane, Wa
May 10, 2017
#13
  • May 10, 2017
  • #13
karthief said:
You will soon be dreaming of mo powa
It starts with a simple 'fresh'n up' then 'well maybe I'll up grade this' and 'a better that' next thing you know you'll be sleeping in the garage, eating baloney sandwiches and drinking PBR so you can buy that turbo because those black marks in front of your house just aren't long enought.
Click to expand...
I like me some PBR regardless of finances

Wow, I just realized we have the popcorn emoji back, @Noobz347 thanks bro!
 
Reactions: General karthief

Noobz347

Stangnet Facilities Maint Tech... Er... Janitor
Admin Dude
Jan 4, 1985
43,563
21,734
234
Box behind Walmart
May 10, 2017
#14
  • May 10, 2017
  • #14
FoxMustangLvr said:
I like me some PBR regardless of finances

Wow, I just realized we have the popcorn emoji back, @Noobz347 thanks bro!
Click to expand...


Um, sure?


I mean... Yes, of course! No problem man. I'm on-top of it.
 
Reactions: General karthief, Davedacarpainter and FoxMustangLvr

Revogen

Active Member
May 10, 2016
104
57
48
May 10, 2017
#15
  • May 10, 2017
  • #15
FoxMustangLvr said:
I like me some PBR regardless of finances

Wow, I just realized we have the popcorn emoji back, @Noobz347 thanks bro!
Click to expand...
PBR FTW!
 
Reactions: General karthief and FoxMustangLvr

HotRodBlack

Active Member
Apr 24, 2017
31
15
28
May 13, 2017
#16
  • May 13, 2017
  • #16
UPDATE

Tear down is complete! It's not good...

Cylinder 1 intake lifter is compromised... the roller is a semi circle. Cam lobes are worn pretty good, lots of pitting. Some of the lobes are squared off.

Every single rod bearing is worn down to the copper. Main bearings are just as bad. Cylinder 5 is physically twisted around and was knocking.

Crankshaft is worn .015 under min spec on the rear two journals... significant scoring present as well, I can catch a fingernail in the grooves.

Cylinder number 8 piston is compromised, it's stuck on its wrist pin.

Didn't pull the cam to inspect the bearings, odds are not in their favor.

Cylinder bores are within spec, no significant loss of cross hatch pattern just worn over time.

The block is salvageable, heads are salvageable, that's about it.

Poor thing was just worn out. Rode hard and put away wet all its life.
 
Reactions: RangerJoe, Davedacarpainter and 90sickfox

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,133
10,749
213
polk county florida
May 13, 2017
#17
  • May 13, 2017
  • #17
Stroker time!

Someone needs to find a stroker emogi
 

mikestang63

SN Certified Technician
Aug 27, 2012
11,606
8,859
214
In the garage
May 13, 2017
#18
  • May 13, 2017
  • #18
explorer motor time
 
Reactions: Davedacarpainter

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,133
10,749
213
polk county florida
May 13, 2017
#19
  • May 13, 2017
  • #19
Stroker explorer motor time
 
Reactions: Mstng93SSP

Blandnuts

I don't swallow; I only swoosh
Founding Member
Aug 21, 2000
1,172
124
124
FloorDuh
May 13, 2017
#20
  • May 13, 2017
  • #20
Cash for clunkers time.
 
Reactions: Noobz347
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

D
For Sale 1993 Mustang LX for parts or restore
  • diesel farmer
  • Oct 6, 2026
  • Fox Body Mustangs For Sale (1979-93)
Replies
0
Views
419
Fox Body Mustangs For Sale (1979-93) Oct 6, 2026
diesel farmer
D
D
sad day
  • davecobra2
  • Jul 13, 2026
  • What is it Worth?!?!?
Replies
2
Views
312
What is it Worth?!?!? Jul 22, 2026
davecobra2
D
Ford truck engine swap issues
  • keel
  • Jul 7, 2026
  • Other Auto Tech
Replies
17
Views
783
Other Auto Tech Jul 13, 2026
General karthief
R
Microsquirt tune for stroked 351W in a foxbody
  • roldy
  • Jul 26, 2026
  • Digital Self-tuning Forum
Replies
7
Views
427
Digital Self-tuning Forum Oct 25, 2026
roldy
R
H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
617
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?