This setup pretty good for the street??

Foxfan88

My Grandpa has great wood.

Sep 13, 2004

2,487

4

0

Miami, Ok

May 12, 2005

#1

• May 12, 2005

• #1

93 roller long block

Thumper heads and bcam combo ( on his site)
Edel Performer carb manifold
Holley 4160 600cfm carb
2000-2500 stall
lentech VB (where can i buy these?)
4.10 gears

and my exhaust that is on my car now
how much hp tq would this be??
any thing i need to change for the better?

What whats the power range on the b cam/ what stall speed should i get???

 

The Fox

New Member

Mar 30, 2005

354

0

0

Port Elizabeth

May 12, 2005

#2

• May 12, 2005

• #2

Sounds good to me aside from the 4.10s for highway; but then again you are runnin an AOD. What's your 1st gear? No idea bout the stall speed I dont bout all that. What is Lentech VB? You gettin an intake with that combo, im gettin an 'Air Gap' to replace my 'Performer' if u want the performer for like $50 plus shipping. I didn't read your sig either so I dunno if you already got em. Runnin larger exhaust or just mufflers? PM if u want the intake. Oh yeah I have an o/r H pipe if u want that for $50 as well.

Anthony

 

90mustangGT

I felt sorry for girls because

Founding Member

Jan 15, 2002

2,773

17

89

Dallas, GA

May 12, 2005

#3

• May 12, 2005

• #3

Sounds like a winner, everything on the same lines, it will run good.

 

Foxfan88

My Grandpa has great wood.

Sep 13, 2004

2,487

4

0

Miami, Ok

May 12, 2005

#4

• May 12, 2005

• #4

so will the 2-2500 stall work good with the b cam???
also i will get rid of my smog pump, my ac that doesnt work and i will never use anyway. and get underdrive pullies.

My exhaust consisted of:
flowtech equal shorties
unknown h pipe( looks like it could be stock with cats cut out)
and some unknown mufflers, it stops before the rear axle.

What do i do about o2 senors, just cut the wire and leave them in there?
Also what do i do about guages??
Will i be required to buy a whole new ignition??

 

Foxfan88

My Grandpa has great wood.

Sep 13, 2004

2,487

4

0

Miami, Ok

May 12, 2005

#5

• May 12, 2005

• #5

Also how much do you think i can sell my old efi stuff for?, if i decide i really like carb....

i got the stock harness, i have stock distributor.
i have a Painless wiring harness( goes for like 450$ in summit)
MSD coil and some aftermarket distributor.


And when the swap is done, what all exactly will be useless and will need to be removed???

 

MrKwik

Founding Member

Jan 29, 2000

1,008

0

0

Kansas City, Kansas

May 12, 2005

#6

• May 12, 2005

• #6

I would bet that the e-cam thumper combo would work a little better with the auto and that stall.

 

B

BaXTeR3221

Member

Jan 12, 2004

917

0

16

Orange County, NY

May 12, 2005

#7

• May 12, 2005

• #7

You can just cut the o2's short and leave them there. Efi computers and harness's can fetch around $150 if they are in good shape.

 

H

h8louzn

Member

Apr 23, 2005

50

0

6

May 13, 2005

#8

• May 13, 2005

• #8

Don't cut the 02 sensors.
Take them out and go to a parts store and get a oil drain plug the same size.
That way if you want to go bace to efi you don't have to buy new 02's.
Just a thought!
And f you sell the painless kit let me know what you want!
Thanks,Eddie

h8louzn@comcast.net