• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

transmission help

  • Thread starter Thread starter natedawg3649
  • Start date Start date Aug 8, 2006
N

natedawg3649

New Member
Jul 3, 2006
10
0
0
MS
Aug 8, 2006
#1
  • Aug 8, 2006
  • #1
I was given a mustang to me and was told that it does not have the original engine it. So i decided to take it out and rebuild it since it had been sitting for about 3 years. Well i got the engine and tranny out and when i went to seperate them the shaft that slides into the torque converter stayed attached and slid out of the tranny somewhat but not all the way. It finally came apart. If i'm correct thats a bad thing but i'm not for sure because i'm used to messing with chevy trannies. I think its an AOD transmission. That shaft is not supposed to come out like that, Correct?
 
S

superhuaman

New Member
Nov 8, 2004
907
0
0
Harrisburg, PA
Aug 8, 2006
#2
  • Aug 8, 2006
  • #2
It's alright if it comes out. Just spin and wiggle and it will go back in (much like you would do when installing a torque converter).
 
N

natedawg3649

New Member
Jul 3, 2006
10
0
0
MS
Aug 8, 2006
#3
  • Aug 8, 2006
  • #3
its alright that it slid that far out, it slides in and out pretty easy
 
S

superhuaman

New Member
Nov 8, 2004
907
0
0
Harrisburg, PA
Aug 8, 2006
#4
  • Aug 8, 2006
  • #4
yep. its all the way in when just the splines show on the input shaft, or maybe a little bit of smooth surface, but not much. you will know for sure that its in if you can successfully reinstall the torque converter.
 
N

natedawg3649

New Member
Jul 3, 2006
10
0
0
MS
Aug 9, 2006
#5
  • Aug 9, 2006
  • #5
does a c4 do that
 
S

superhuaman

New Member
Nov 8, 2004
907
0
0
Harrisburg, PA
Aug 9, 2006
#6
  • Aug 9, 2006
  • #6
yeah. c4's have an input shaft inside another shaft looking thing with splines, but it doesnt rotate. that is the stator support, for inside the torque converter. then of course the converter hub drives the pump.

aod's are the same way, except there are two input shafts, 1 solid, and the next one around that, which is hollow. then the stator support. So, i guess a c4 converter should "clunk" and go in about three times while youre installing it...and an aod converter should "clunk about four times. i will try to dig up some pictures later.
 
You must log in or register to reply here.

Similar threads

T
Drivetrain TREMEC TKX 1–2 Grinding Issue at ~4,000 Miles + Poor Warranty/Customer Service Experience
  • Ttopfoxguy
  • Oct 10, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
343
Fox 5.0 Mustang Tech Oct 15, 2026
JMG9350
J
Drivetrain How much resistance, if any at all, is normal on a new 1st gear and synchro on a WC T5 transmission?
  • sleep-e
  • Jan 21, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
350
Fox 5.0 Mustang Tech Jan 22, 2026
sleep-e
P
2002 T5 transmission vibration issue
  • puffoo
  • Feb 22, 2026
  • SN95 V6 Mustang Tech
Replies
0
Views
303
SN95 V6 Mustang Tech Feb 22, 2026
puffoo
P
J
88 Foxbody 5.0 Driveshaft Issue! Need Help
  • James Hood
  • May 1, 2025
  • Fox 5.0 Mustang Tech
Replies
3
Views
578
Fox 5.0 Mustang Tech May 1, 2025
AeroCoupe
9
Engine Donor '00 Mountaineer meet '91 Fox
  • 91firecracker
  • May 11, 2026
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
41
Views
1K
Fox 5.0 Mustang Tech May 28, 2026
91firecracker
9
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?