• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Which Cam For Mild Engine

  • Thread starter Thread starter dcurtis
  • Start date Start date Feb 14, 2006

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Feb 14, 2006
#1
  • Feb 14, 2006
  • #1
Finished all of the body work I plan to do on my 93GT (cowl hood, saleen wing, cobra r's, and shaved doors) now it's about time to pull the engine and do a basic rebuild on the bottom end and switch the pistons to give me about 9.5 to 1 compression with rebuilt stock heads, new valves, springs etc etc, probably going with the cobra upper and lower intake with??? heres where im not sure.
What would be the best cam for my present combo, the e303, f303,b303, or maybe even the x303, also what size fuel pump, maf, throttle body and injectors would I need for that cam, I would like the cam to good lope to it, but not if it would be to big for the heads and intake, also it does have a t5 tranny if that matters.
Sorry if my question is a little confusing or anything but this is the first ford build I've ever done so I don't know what will work with what, also do the stock 302h.o.'s have 1.5, 1.6 rockers or what? and are the above cams sized with 1.5 or 1.6 rockers
 

25thmustang

Mustang Master
Sep 5, 2003
2,021
85
99
Montgomery, NY
Feb 14, 2006
#2
  • Feb 14, 2006
  • #2
I would say for a nice sound and decent power, and E or B cam woul work well. Throw a set of 1.6 roller rockers on there, 155 fuel pump, 75mm MAF, stock or 24 lb injectors, and a 65 or 70 mm TB and you should be all set!
 
8

89white50

Member
Nov 16, 2004
440
1
18
central MA
Feb 14, 2006
#3
  • Feb 14, 2006
  • #3
stock is 1.6 rr
 

stangjunkie

New Member
Nov 15, 2004
381
0
0
Feb 14, 2006
#4
  • Feb 14, 2006
  • #4
lol!! and 110 pump and four tires cast iron heads, and make sure you upgrade roller cam though...

seriously e cam would be good if you plan on stil doin more get the b-cam and save the time of doin it twice
 

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Feb 14, 2006
#5
  • Feb 14, 2006
  • #5
Ok I decided to use the trickflow track heat intake instead of the cobra, with a 155lph pump 24lb injectors, 1.6 roller rockers and the b303 cam, do I need the egr intake or not, also does the throttlebody need to have a tps sensor or not, what throttle body and maf would you recommend, sorry but I have no clue to what I need from between the intake to the cold air kit.
Thanks for your help, its really needed
 
B

BaXTeR3221

Member
Jan 12, 2004
917
0
16
Orange County, NY
Feb 14, 2006
#6
  • Feb 14, 2006
  • #6
you need the tps and you'll need an egr spacer as well. The spacer is integrated on the cobra intake, but not with others. A lot of times, throttle bodies come with the spacer. 70mm throttle body and a 75-80mm MAF is a reliable combo.
 
T

Topdowncruise

New Member
Apr 7, 2005
207
0
0
Canada
Feb 14, 2006
#7
  • Feb 14, 2006
  • #7
Are you sure you want to just rebuild the stock heads?You could get better flowing aluminum heads or at least upgrade your stock heads (porting etc) for not much more money.If you are staying with stock heads I would recommend the cam you have right now:the stock one,and maybe add 1.7 roller rockers.
 

95opal

5 Year Member
Nov 16, 2004
449
20
39
Feb 14, 2006
#8
  • Feb 14, 2006
  • #8
track heat intake with stock heads ?? A little to big for that set up
 

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Feb 15, 2006
#9
  • Feb 15, 2006
  • #9
my stock heads will be ported and polished, and probably gasket matched to the intake. So, the ford racing cobra intake would be the better choice and I wont need to order an egr spacer or plate? Also, on the B303 camshaft it's rated at .480 lift, is that .480 lift with 1.6 rockers?
 

timewarped1972

Member
Jun 17, 2004
642
0
16
mesa, az
Feb 15, 2006
#10
  • Feb 15, 2006
  • #10
yes their all rated at 1.6.

the B cam is less lift more duration than the E, and the E is less duration more lift than the B , i believe they are ground on different lope seperation angles as well which is where the B gets it's lopey ness from...and why the E is smog legal and the B is not..
 

craigwhite89gt

New Member
Oct 26, 2003
181
0
0
Cecil County Maryland
Feb 15, 2006
#11
  • Feb 15, 2006
  • #11
sounds like everyone has you going in the right direction.. But if you want opinions here i would def get some aftermarket heads....Thats quite a bit of porting that would be done to make stocks flow... As far as cam go's it depends on what you want the motor to do.....Boosted or N/A? My set up is as follows...

306 SLP pistons Stock crank and rods
F- Cam
Aluminum Strike Force heads 2.02/1.60
Trick flow STREET intake manifold 70MM TB
30# inj
1.6 RR
Canton Lower girdle

Now i chose the F cam becuase i plan on boosting the motor..
This cam has great torque around 2000 range for highway but the HP jus feels like it keeps climbing as the RPMs go up... Just my 2 cents for ya...

Goodluck
 

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Feb 15, 2006
#12
  • Feb 15, 2006
  • #12
how do you think the BBK SSI intake would work with the b cam, it also has the egr already there like the cobra intake, I think, plus it comes with a BBk 70mm throttle body calibrated for 24lb injectors and high flow BBk fuel rails.Do you think it would perform better than the cobra intake?
Also, I have been looking for the best place to buy the cam from and I have seen it rated at two differant lifts, one has it as B303, 284 284 duration .480 intake .480 exhaust lift and the other has it marked as 284 284 duration .480 intake .498 exhaust. So which is correct?
 

gcwh02

New Member
Jun 20, 2005
515
0
0
pottstown, PA
Feb 15, 2006
#13
  • Feb 15, 2006
  • #13
dcurtis said:
how do you think the BBK SSI intake would work with the b cam, it also has the egr already there like the cobra intake, I think, plus it comes with a BBk 70mm throttle body calibrated for 24lb injectors and high flow BBk fuel rails.Do you think it would perform better than the cobra intake?
Also, I have been looking for the best place to buy the cam from and I have seen it rated at two differant lifts, one has it as B303, 284 284 duration .480 intake .480 exhaust lift and the other has it marked as 284 284 duration .480 intake .498 exhaust. So which is correct?
Click to expand...

Throttle body isnt what you need to calibrate for the injectors, it is the mass air flow.
 

Aliate X

Member
May 9, 2005
602
1
18
Rockland NY
Feb 15, 2006
#14
  • Feb 15, 2006
  • #14
save a few extra bucks and get yourself some used aluminum heads on corral for like 700-1000, youll be happy you did and you can run a bigger cam b/c I know you want it to lope heh.
 

legalize420

Active Member
May 21, 2005
1,541
1
37
South Florida
Feb 15, 2006
#15
  • Feb 15, 2006
  • #15
dcurtis said:
how do you think the BBK SSI intake would work with the b cam, it also has the egr already there like the cobra intake, I think, plus it comes with a BBk 70mm throttle body calibrated for 24lb injectors and high flow BBk fuel rails.Do you think it would perform better than the cobra intake?
Also, I have been looking for the best place to buy the cam from and I have seen it rated at two differant lifts, one has it as B303, 284 284 duration .480 intake .480 exhaust lift and the other has it marked as 284 284 duration .480 intake .498 exhaust. So which is correct?
Click to expand...



its 224 224 and 480 480
 
You must log in or register to reply here.

Similar threads

D
N/A build on fresh stock 302
  • djcarrot
  • Oct 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
12
Views
457
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 19, 2026
AeroCoupe
9
Engine Donor '00 Mountaineer meet '91 Fox
  • 91firecracker
  • May 11, 2026
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
41
Views
1K
Fox 5.0 Mustang Tech May 28, 2026
91firecracker
9
J
Intake
  • James S
  • Jul 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
10
Views
308
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 12, 2026
James S
J
A
Discussion on mild budget build/ top end
  • Acesario
  • Feb 21, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
20
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 23, 2026
General karthief
N
Looking for ECU/CHIP for 1992 5.0
  • Nathan26
  • Sep 26, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
9
Views
339
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 8, 2026
Qtrhrse23
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?