Search results

  1. mikec35

    94 Black Leather Factory Seat Upholstery Needed

    I am a vintage guy putting 94 mustang black leather seats in my 67 mustang. The passenger is perfect, drivers side upper is perfect but the drivers side lower needs to be replaced. Does anyone sell oem seat leather? I'd like to match what's currently there instead of redoing both seats. Any...
  2. mikec35

    Wheels-Tires 67 Shelby clone, Shelby 10 spokes or Vintage Wheels v50

    I'm still trying to decide what wheels I want on my clone, what do you think is the better choice, Vintage Wheel Work's v50's or Shelby 10 spokes? I am thinking 15 x 7's, not sure what size tires I want. Suggestions for either of the 2 wheels mentioned and tire size would be great. I had 14 x...
  3. mikec35

    5 years later, my 67 Shelby clone is painted and home..

    Finally I have my car home and I am ready to start putting in back together...Not sure where to start...I need to figure out if I want to use dynamat or fatmat, I have the tar floor pieces and carpet already. Then on to the painless wiring harness... then who know's what.. A couple of...
  4. mikec35

    Labor Cost To Install Mustang Ii Front Suspension

    I've been away from my project for a couple of years... divorce, moving...and now I am getting excited to get started again. My 67 FB Shelby clone is in need of a front suspension upgrade. What kind of ballpark figure would I look at to have a Mustang II front suspension installed ( Labor only...
  5. mikec35

    How Much To Paint Stripes On 67 Clone

    How much should I expect painting le mans stripes would add to the cost of my paint job? I am finally getting my 67 FB shelby clone painted after 5 years worth of work ( and collecting dust ). It has been blasted, rusted metal cut out and replaced and shelby fiberglass added. I have a price...
  6. mikec35

    67 hood hinge/ fender apron mount nut ?

    Does anyone know where to get the half round nut that sits in the fender apron? I looked in a few catalogs and did not see it. Is it hard to get out? Thanks, Mike...
  7. mikec35

    67 fb factory wire harness question

    I have been debating a while whether to get a factory underdash harness or a painless. I have decided to get the factory harness. I have a couple of questions. How much less work is it to install the factory harness vs. the painless? I would suspect quite a bit. Also, my car has no tach...
  8. mikec35

    installing aluminum dash inserts

    How hard is it to install brushed aluminum dash inserts? Do they line up good? Do they look good? Trying to decide if I want to order the inserts to install on my dash pieces or order the aluminum dash pieces themselves. For a 67.. there is quite a big price difference between the two...
  9. mikec35

    Tips for keeping overspray out of cowl?

    I split the cowl on my 67 fb, repaired it and painted it. Now that its back together and I am doing body work does anyone have any tips how to keep overspray and sanding dust out? I know I can keep it covered most of the time but when working on the cowl area itself or when painting the car I...
  10. mikec35

    granada swap info needed

    I took the front disk brake assembly off of a 76 (I think) granada at a junk yard about 10 years ago and they have been sitting in my garage ever since. I am getting ready to clean them up and install on my 67 fb. I do not remember if they came off a power brake car or not. Does it make a...
  11. mikec35

    67 shelby clone gap front nose to fender

    Anyone have any pics of the gap between the front nose and the front fenders? Mine are filling up with primer and I need to know how much to cut. Thx
  12. mikec35

    67 fb hood pin install advice needed

    Does anyone have some pictures/measurments for installing the standard shelby style hood pins? This is the last thing I need to do at the body shop this week before taking my car to the paint shop. Thanks...
  13. mikec35

    67 shelby clone functional scoop quest..

    Anyone know where to cut the wheel well for the functional side scoop? The plastic adapter that Branda sent with the kit seems to fit "ok" on the inner wheel well, but I think it should mount to the outer wheel well.. any advice or pics? Thx, Mike...
  14. mikec35

    need pic of 67 door front gap

    Doe's anyone have a close up picture of the front door gap at the top? I had door skins put on my original doors and the gap does not look right where the top of the fender and the door meet. Thanks
  15. mikec35

    67 fb shelby clone hood, which one?

    Getting ready to order my hood from Branda, I like the one with the side louvers but is it period correct for a 67 or is the hood without the side louvers correct? I want to get the right one. Any advice?
  16. mikec35

    Monte carlo bar install 67 fb

    How much would you expect to have to spread the shock towers to make one of these fit? I have a curved one that is a full 1 inch too long. I think it was made too long. My car is dead level with no engine/transmission. Spreading the shock towers 1 inch is way too much. Anyone have a...
  17. mikec35

    67 fb shelby tail panel install question..

    I have a fastback that I am converting to a shelby clone. Got the tail panel with the open cut outs and plan to use the mustang project tail lights. Whats the best way to attach this panel to the existing tail panel? It has some tabs at the bottom, but it looks like it needs to be spaced out...
  18. mikec35

    67 FB, where to mount "E" brake brkts?

    I have new floors and had to order the emergency brake brackets. Does anyone know where to weld these? Thx
  19. mikec35

    floorpan paint question

    Part of my floors are epoxy primed and the new replacement floors are bare metal. I wan't to paint them red as they came from the factory. Is zero rust a good solution? I know it would be good over the bare metal, but what about the expoy primer? Maybe I will epoxy prime the new metal then...
  20. mikec35

    2007 shelby exhaust

    What exhaust set up comes with this car?
Top Bottom
Back
Forums
Menu