Search results

  1. 1fastsn95

    87 stalling when going into gear (auto)

    my 87 stalls when I put it in reverse or drive after it warms up. Its fine all day long as far as starting and stopping, but when I have to put in reverse it stalls out. Then itll stall going back into drive. I can give it a little gas, get it moving, and itll be fine. Just that initial "switch"...
  2. 1fastsn95

    LRS/50 resto seat covers

    Has anyone used LRS/50 resto replacement seat upholstery? I got a set of grey sport seats that have some cig burns in them. Ive changed my int to black so I either need different seats or just recover the grey ones. (black of course). So Im wondering if those that have used them are satisfied or...
  3. 1fastsn95

    5 lug swap parts list

    ok ive searched this forum but havent found the exact answer Im looking for so please dont bash me for"not searching". Im wanting to go the cheapest way possible. I already have: 2 spindles, rotors, and brake calipers from a 94 V6 model. I "think" I am gonna use 2 ranger driver side axles/drums...
  4. 1fastsn95

    broken valve spring, now what?

    My car developed a miss. So after all the plug, plug wire check and compression check, realized it had to be something under the valve cover. Sure enough, broken valve spring. So, can I just order one or do I have to get a whole set? And all I know about them is they are dual and they came with...
  5. 1fastsn95

    header help...

    Im looking for a new set of headers for my 94. I have Hedman equal lengths and I hate em! They burn up my clutch cables, they take up too much room, and they leak. Since my EGR and smog stuff is disconected, can I use pre-94 type headers? Or would I be better to by 94-95 type and weld shut the...
  6. 1fastsn95

    Just a little help here...

    All these people that eliminate their ACs, I know someone out there has the hose that goes from the compressor to the accumulator. Ive looked everywhere and cant find squat. Except for Prestige Mustang who want to RAPE someone!! Ive checked ebay, stangnet, craigslist and cant come up with...
  7. 1fastsn95

    Why does my car seem so sluggish? Cam?

    the basics: .040 302, TFS heads (2.02/1.60), B cam, 1.6 RRs, Cobra intake, 70mm TB, 73mm MA, 24# (fp @ 38#), Timing @ 14 deg, AOD (no stall), 4.10 gears. This thing is a DOG outta the hole, after about 24-25k rpms it starts pulling pretty decent, but not like I was expecting. What should I...
  8. 1fastsn95

    Need opinions on door panel problems

    Ok I just bought a full black interior for my 87. The problem lies within the door panels. My car has manual roll downs and locks. The black door panels are for electric. Should I : (A) Sell them and try to find ones for manual? (B) Find manual door handles and drill a hole for the knob? (C)...
  9. 1fastsn95

    instrument cluster swap, will it work?

    ok the instrument cluster in my 87 is in sad shape. Looks like it sat in the sun for years. The numbers are faded and cracked and just look bad. I found an 89 (85mph speedo) 4cyl at the junkyard with a perfect cluster. Can I simply swap them out? Plug and play?? Thanks!!
  10. 1fastsn95

    Lets talk ACs...

    ok I know its still winter but Im already dreading the summer here in Tenn. My AC is shot. What other Ford ACs will work on a foxbody? I found a 90 (I think) Mark 7 LSC that looked fairly close but Im not sure. I hit the valve on the line and Refrig. came out. Im guessing its probably still...
  11. 1fastsn95

    just a quick "thank you"

    Hey folks, just wanted to say thanks to everyone that has helped me find info, suggestions, links, and commented on my recent motor swap. With everyones help I hurdled many obsticles with this project, the biggest being the SD to MA swap. Also all the simple questions like valve sizes, cam...
  12. 1fastsn95

    new gauges, need some assistance

    I got new oil pressure and water temp guages. Where do they go?? If I put the WT where the factory sensor is, what do I do with the wire? Same with the OP guage. Or is that even where I need to put em?? Any help is greatly appreciated! Pics would really be great too! Thanks!! Chris
  13. 1fastsn95

    trying to finish engine install, few Qs...

    ok Im bout done with my engine swap in my foxbody. A few questions I have: First, Where does the ground from the battery mount? And the bracket for the starter wire? Do they go together? Also, I have a bracket behind the intake for the TB cable. Where does it mount? And finally(for now!), I have...
  14. 1fastsn95

    Need a bolt size!

    This is for the ground strap from the firewall to the back of the block. Need the size that goes to the block. Thread size and length. Thanks!!!
  15. 1fastsn95

    Q about header gaskets.

    Which way do these go?? Shiny/metal side or black/paper side inside or outside? Or header side, head side? Thanks!!
  16. 1fastsn95

    help w/ valve covers

    I need a set of valve covers. My stockers are too short for my RRs. I have a set of trickflow valve covers that are too tall for my intake(theyre beat up anyway). SO I can only assume that Ill have to have a phenolic(sp?) spacer for the intake to clear a tall set of VCs. Is there a shorter...
  17. 1fastsn95

    does a 5.0 have an oil deflector??

    My engine builder says Im suppose to have an oil deflector. i cant find one in my "pile o' parts" from my old motor. But, when I was dissassembling the old motor, I busted the timing cover and scrapped it. Dont think there was one attached to it :shrug: and one other thing, my engine builder is...
  18. 1fastsn95

    cam selction

    Help me out folks! Im just about ready to assemble the new 308 but Im not sure what type/brand/style cam to go with. I already have a B303 cam, but its kinda outdated. I like the way the bcam sounds, but I know I can go bigger and get more outta my motor. My pistons have valve reliefs, I have...
  19. 1fastsn95

    cam degreeing!?!?!

    Will someone please school me on the advantages/disadvantages/reasons for advancing or retarding a cam??
  20. 1fastsn95

    send me some cam/exhaust vids!

    ok guys, I want some vids/sound clips of cars with lumpy/aftermarket cams. Tell me what kind of cam and what kind of exhaust youre runnin. Everybody else give your opinions!!
Top Bottom
Back
Forums
Menu