help

Hello all, Lend me your ear and I’ll tell you a story... or skip to my question. In 2010 my father and I came across a 95 mustang owned by some ‘strange’ folks. The type that would hide when someone knocked at the door, the kind that wouldn’t answer their phones for weeks to months at a time...

Hey guys, nice to meetcha. Everyone who helps or tries to has my deep appreciation haha. I just recently got a neglected 2000 Ford mustang. And I've been restoring it a bit and replacing all sorts of things. Unfortunately it was ghetto rigged so I've been working around that. However it's been...

04 gt, just replaced my belt and idle pulley, I dont know what I did, but the belt tensioner is rubbing on the timing cover, my belt routing looks good, my idle pulley looks fine, I think from pulling the tensioner and it being OEM it might just be worn, I adjusted everything and it doesn't run...

2004 gt, factory intake manifold, this bolt hole behind the throttle body towards the passenger side, goes into the plastic manifold, what's it for? Just wondering if somethings supposed to go there. (In the photo it's the hole with the brass sleeve there, between the TB spring and cable)

All I’m getting is a single click when trying to start up my fox. I’ve checked the battery it’s good and I’ve replaced the ign switch as it was getting loose. This is my daily and it happened minutes after it was cranking perfectly fine. Below a video that shows me testing at the solenoid. Goes...

I don't know too much about cars but I recently bought a 1969 mustang and I decided to rewire using American auto wire (AAW) and I finally finished and ready to start the car, when I put the key into the on position the car immediately tried starting without me turning the key, it also made this...

So, I am acquiring some GT40 heads from a buddy of mine. They have port work, bowl work, o-rings, decked .060 and have the correction cut on the intake side. I'm looking to see if I just use a standard 9333pt1 head gasket with o-ringed heads and if having GT40 heads milled .060 will I run into...

Hey Guys, I am havin a NIGHTMARE with my f***ing car. I had the manifold break and i didn't want to install another :poo: plastic one so i bought this one. Now i am popping codes P0171 and P0174, lean system. Yes, i know there are sensor possibilities, injector issues, and what not, but before i...

I've got a automatic 2004 gt, the transmission shifts fine, not particularly smooth, but acceptable. After braking hard without stopping like entering a corner, the transmission let's go like it's in neutral and wont re-engage for a second or two, it will just rev up freely and then snap back...

I come from fox bodies, so I'm new to the 4.6. I'm wondering if my 04 has the upgraded manifold? Under load on the freeway it gets a little bit of shaking like its motor mounts, but it seems solid at idle, any ideas what it could be? Heres some photos of my manifold. Thanks

Totaled (according to insurance) mustang in a crash Monday.. Please just help me with advice because I don't know where to start

hey i have a 2005 mustang gt i saw that the 2009 has the factory ambient lighting in the cupholders and the button, is there anyway too find those parts anymore for a upper center console swap? i looked parts says discontinued and ebay is dead.

I have a 2000 GT and I ordered a new hydro-boost. I was wondering what the process and steps are to change one out. Do I have the bleed any fluids and replace them? Do I have to purchase and new gaskets and or o-rings?...etc

Hi All! I am restoring a 1973 Mach 1 Mustang, and am looking for some rear window louvers. I'd like to buy some used ones for less than 300. ( I can buy brand new ones of cjponyparts for 300) If any of you guys have any suggestions (or unused louvers) PLEASE let me know! Thanks! Here's a pic...

So my 01 bullitt is experiencing some steering issues, there is about a half inch to an inch of play in the wheel only when turning it to the left, no issues when turning right. No wobble or noises at speed. I’m thinking it’s maybe a tie rod or steering shaft. If anyone could help me figure out...

I was replacing the oil pressure sender on my 1989 mustang 5.0 when I accidently knocked a plate off this hole. It was very badly attached by a previous owner and I have no idea what belongs here. I found pictures of what goes here but I have no clue what it is or does. I’ve been running my...

Hey there, i need Help. I got an 69’ Mustang with AOD trans. But now i wanted to start the car, but just connect battery cable with battery and then it starts. The ignnition switch - off position. If i wana shut down the car i must disconnect battery cable. I changed solenoid, new ignition...

I want to to put as wide of a rim and tire I can on my 1998 Mustang Cobra without making any serious mods to the suspension except I do want to drop it 2”s. I want the car as low as I can and I want the tires to be as wide as I can fit in the wheel wells and not have the rear wheels and tires...

Hi everyone I'm 17 and recently bought myself a 2006 mustang gt as my graduation present to myself. Any who I've been looking at power mods for my mustang and stumbled across Department of Boost and I was blown away with the price and raving reviews of the product. One problem though, I live in...

Will these rims work on my car? I have sn95 front spindles and stock rearend with drum brakes and 5 lug conversion. And I will run the 17 inch rims that are 8.5 wide.