Progress Thread 12th Owner: My '93 Notchback Restoration & Performance Build

Rdub6 · Dec 20, 2020

Habu135 said:
No, I definitely will. I'm just not skilled in TPS language and need to read up on it.

If you have a digital volt meter, it’s as easy as putting some pins into the wires, and then watching voltage as you move the the throttle blade.
I use pins like these to put into the back of the plug, then touch my DVM probes to the pins.

Rdub6 · Dec 20, 2020

I put them in this side of the connector, and then take my readings from the pins.

Habu135 · Dec 20, 2020

I love it. I'll accomplish it tomorrow. Big thanks.

Rdub6 · Dec 20, 2020

Habu135 said:
I love it. I'll accomplish it tomorrow. Big thanks.

As you move the throttle, you should see a very even rise in voltage if you have good connections.
If it jumps around, or if there are dead spots, then the TPS is most likely bad.

Habu135 · Dec 21, 2020

Going through my car visually before I start on the TPS. I can fresh antifreeze dripping down from between the timing cover and front of the engine block. I'm thinking this would clearly be letting unmetered air into the engine. Ugh.

Mustang5L5 · Dec 21, 2020

would be difficult for air to go in there and make its way to the intake track. If anything the coolant pressure would force coolant out and not allow air in.

however it needs to be fixed obviously

Habu135 · Dec 21, 2020

Mustang5L5 said:
would be difficult for air to go in there and make its way to the intake track. If anything the coolant pressure would force coolant out and not allow air in.

however it needs to be fixed obviously

Yep. I can't find anything else obvious and I've tried the basics.

The symptoms are I drive the car normally and it's fine, but if I accelerate hard the car's character changes and it displays hesitation and bucking.

Habu135 · Jan 1, 2021

Car ended up having a blown timing chain cover gasket. Seems to be happy now.

Mustang5L5 · Jan 1, 2021

Vac leak?

Cheapskate207 · Jan 1, 2021

I don’t think there is vacuum there?

Mustang5L5 · Jan 1, 2021

Would be just crankcase vac.

Habu135 · Jan 1, 2021

Mustang5L5 said:
Would be just crankcase vac.

I think it was blowing out a lot of air. Oil filter clearly had streaks on it and it was leaking A LOT of coolant and oil.

Cheapskate207 · Jan 1, 2021

Interesting, learn something new everyday. Glad the car is fixed!

Habu135 · Jan 1, 2021

Cheapskate207 said:
Interesting, learn something new everyday. Glad the car is fixed!

Knowing's half the battle.

Mustang5L5 · Jan 1, 2021

I would have never thought to suggest that. But then again, that’s probably something you’d just notice on the car which would cause you to investigate it

Habu135 · Jan 4, 2021

The rear main seal in my car is leaking constantly and naturally is annoying the hell out of me. I'm planning on pulling the trans, replacing the seal, resurfacing the flywheel and installing a new clutch while I'm in there. I'm looking for suggestions. My car will likely be under 400 rear wheel horsepower when it's finally done. Meaning all naturally aspirated with no nitrous or supercharging. I know the Valeo King Cobra is under $100 and is a popular choice. I was actually leaning toward the Ford Performance M-7560-A302N. Thoughts? My mindset is do it once correctly and not deal with it again.

Thanks and yes I did research this in past Stangnet forums before I posted this.

Mustang5L5 · Jan 4, 2021

Looks like a lot have changed with King Cobra clutch kits. Seems a few have come and gone. But looking back, it appears I ordered a M-7560-C302 clutch kit back in early 2000's. It's been discontinued. Looking at pics of my disk, it's a M-7563-C302 pressure plate and a M-7560-A302 clutch disk in the package (along with a D9ZZ-7548-A throwout bearing)

The C302 (and C302N) Pressure plate have the same capacity as the M-7563-B302 pressure plate (25% more than stock Mustang clutch), but 10% less effort.

But this A302N kit has the M-7563-A302N pressure plate that is 40% stronger than the stock Mustang clutch. No reduction in pedal effort though.

So the A302N kit is stronger than than the older King Cobra clutch kits, but lacks that slight reduction in pedal effort. I'm putting my older kit behind ~325HPish, and i'm not losing sleep over it. If i had to buy a kit, looks like i would get the A302N kit.

Habu135 · Jan 31, 2021

I have a slight space, just a crack, between the window weather strip and the window trim. At speed it is noticeable as window noise. Although I've never seen old weather stripping pushed down, is it possible to be laid flat over time creating a space? Otherwise the weather stripping is in excellent condition.

90sickfox · Jan 31, 2021

The door looks like it needs to go back a little bit. Looks like its just barely catching the inside edge of the weatherstripping.

That quarter window looks amazing. It's been so long since I've seen one that looked that good.

Habu135 · Jan 31, 2021

90sickfox said:
The door looks like it needs to go back a little bit. Looks like its just barely catching the inside edge of the weatherstripping.

That quarter window looks amazing. It's been so long since I've seen one that looked that good.

Thanks. FoxResto for the quarter windows.

Ya, I'm thinking the weather stripping is somewhat flat. I played with pushing it up and it seals, but within a day or two it goes back down.

Progress Thread 12th Owner: My '93 Notchback Restoration & Performance Build

Rdub6

So while I wait to figure out my rear end issues

Rdub6

So while I wait to figure out my rear end issues

Habu135

Rdub6

So while I wait to figure out my rear end issues

Habu135

Mustang5L5

That is…until I whipped out my Bissell

Habu135

Habu135

Mustang5L5

That is…until I whipped out my Bissell

Cheapskate207

The left one hangs a little lower

Mustang5L5

That is…until I whipped out my Bissell

Habu135

Cheapskate207

The left one hangs a little lower

Habu135

Mustang5L5

That is…until I whipped out my Bissell

Habu135

Mustang5L5

That is…until I whipped out my Bissell

Habu135

90sickfox

Wasn't a pretty sight...and I've got big hands

Habu135

Similar threads

Progress Thread 12th Owner: My '93 Notchback Restoration & Performance Build

So while I wait to figure out my rear end issues

So while I wait to figure out my rear end issues

So while I wait to figure out my rear end issues

That is…until I whipped out my Bissell

That is…until I whipped out my Bissell

The left one hangs a little lower

That is…until I whipped out my Bissell

The left one hangs a little lower

That is…until I whipped out my Bissell

That is…until I whipped out my Bissell

Wasn't a pretty sight...and I've got big hands

Similar threads

Privacy & Transparency

Privacy & Transparency