Progress Thread 88 Gt T-top- Project problem child

Noobz347 · Jun 4, 2017

billison said:
Ok. Put the car through a couple heat cycles and so far so good with a couple exceptions.

My aftermarket temp gauge broke and I managed to loose the probe so yeah.

But the big one is I'm getting some major light deming when the e fan kicks on. Significantly more than before the wire tuck. I may need to add some extra grounds at maybe a controller with a soft start later.

What is the fan setup like? Do you have a controller or relay setup? How is it wired?

Chuckman · Jun 4, 2017

billison said:
Starting to pull the interior, anyone know what I'll run into when I get to the headliner? Anything I should look for?

Once you pull the door, windshield, and hatch trim, there's just one or two retainers on each side above the doors and the dome light that hold it up. There's also insulation separate from the headliner that's just glued to the roof.

billison · Jun 4, 2017

Noobz347 said:
What is the fan setup like? Do you have a controller or relay setup? How is it wired?

It's the contour fan set up. I'm using a Hayden adjustable temp controller and then I added a relay. The controller turns on the relay. I did it this way to protect the controller.

Noobz347 · Jun 4, 2017

...and your alternator? 130 amp? What battery do you use?

billison · Jun 4, 2017

3G alt. Just a standard battery.

billison · Jun 4, 2017

As far as the fans, the fans and headlights all ground to the front rad support, I'm hoping adding a ground strap from the block or alt to that area will help.

billison · Jun 11, 2017

Maybe I'm using the wrong name, but is the Chanel retainer reproduced for our cars? Mainly the rear ones?

View: https://m.youtube.com/watch?v=FSaectAM7_E

Davedacarpainter · Jun 11, 2017

Not that I know of Bill, are yours damaged?

billison · Jun 11, 2017

One has a chunk missing, and I'm still dealing with a stripped screw on another

Davedacarpainter · Jun 11, 2017

I'll see if I can find some for you at the salvage. So you need both sides?

General karthief · Jun 11, 2017

Pics of what you need, I have a 91 vert parts car.

billison · Jun 11, 2017

I'll snap some pics today. I'll know later on today what I need. The passenger side is for sure damaged, won't know about the drivers till I get this screw out. They were removed before and some of the screws were pretty bad. On
The plus side, this is the only stripped anything I've found in the car, and there seems to be very little damaged plastic on the interior.

billison · Jun 11, 2017

Got the other side out. Both sides have this section missing... is that factory?

Davedacarpainter · Jun 11, 2017

I don't remember from my red car, I haven't taken them off of the blue car yet. I'll do a little research.

Davedacarpainter · Jun 11, 2017

Ok, yes, that cutout area is supposed to be there.

Look at this t-top weatherstrip guide. http://foureyedpride.com/fep_bild/v/img_arch/tech/troof_leak/pg25.jpg.html

billison · Jun 11, 2017

Both sides were the same so that is why I'm asking. Just a few more things and the interior will be out. Hoping for today. The headliner is glued all around the t tops though, hoping I can save it.

billison · Jun 11, 2017

Davedacarpainter said:
Ok, yes, that cutout area is supposed to be there.

Look at this t-top weatherstrip guide. http://foureyedpride.com/fep_bild/v/img_arch/tech/troof_leak/pg25.jpg.html

Sweet! Then mine are good! Those areas are caked in weatherstrip glue.

billison · Jun 11, 2017

Ok! So far so good. Almost no rust at all, just a little surface rust behind the seats. The rest is clean. The drivers side looks like a possible replacement floor? Gonna give the paint thread a bump and ask about clean up.

billison · Jun 17, 2017

Hey Dave. Need a little advice. Removed the upper t top trim. I knew I was gonna have to replace at least one rivet but I'm probably gonna do them all. The ones in here are a cheap aluminum and are breaking easy. I need something stronger so it'll hold the metal up that holds the roof sheet metal up.

Any advice on what size and type I should get?

Davedacarpainter · Jun 17, 2017

I'll have to do a little snooping, I'll get back with you Bill.

Progress Thread 88 Gt T-top- Project problem child

Stangnet Facilities Maint Tech... Er... Janitor

GTFO you fat, heavy bastard

I like tinted tail

Stangnet Facilities Maint Tech... Er... Janitor

I like tinted tail

I like tinted tail

I like tinted tail

Chicks can make things hard if they’re inspired...

I like tinted tail

Chicks can make things hard if they’re inspired...

wonder how much it would cost to ship you a pair

I like tinted tail

I like tinted tail

Attachments

Chicks can make things hard if they’re inspired...

Chicks can make things hard if they’re inspired...

I like tinted tail

I like tinted tail

I like tinted tail

Attachments

I like tinted tail

Attachments

Chicks can make things hard if they’re inspired...

Similar threads

Privacy & Transparency

Privacy & Transparency