Do I need wheel spacers? (Pics inside)
- Thread starter bcollie67
- Start date
streethorse
15 Year Member
Not needed, looks well balanced as is. Spacers IMO is just another
point of failure and extra weight.
point of failure and extra weight.
EPIK
Member
Yeah I think it would too. Wouldn't I need longer studs when doing 1/4 spacers? Also do you think the tires would rub the fenders when going over uneven surfaces?
Just get some 315s back there
Will 315's even fit on a 9 inch wheel? If not whats the largest tire that will fit?
Watch out, thats the mating call of the Bakos bird.... too late
Damn it Laser!! I knew I shouldn't have typed that right after I hit submit.
BurningRubber
10 Year Member
- Dec 6, 2004
- 1,865
- 24
- 58
Do you have any shots straight on from the rear of the car?
It looks like your axle is shifted to the right a little. Mine is the same way and I havn't seen many other cars with the same problem.
Its maybe 1/2-1" in most cases.
It looks like your axle is shifted to the right a little. Mine is the same way and I havn't seen many other cars with the same problem.
Its maybe 1/2-1" in most cases.
I don't think thats the case at all. Just might have seemed that way from the difference in angles from the first two pics.
I have 1/4 in. spacers on my rear wheels with the stock studs
Your car does not need wheels spacers
Your car does not need wheels spacers
68stang351
Founding Member
Looks good to me. I think Mustangs with stock wheels definitely need spacers though. Here's before and after on my stock Bullitt wheels. I got a good deal on some 1.5 inch spacers so I jumped on it.
Before:
After:
Now tell me that it doesn't look 100 times better! They should sit like this from the factory!
Before:
After:
Now tell me that it doesn't look 100 times better! They should sit like this from the factory!
BurningRubber
10 Year Member
- Dec 6, 2004
- 1,865
- 24
- 58
I don't think thats the case at all. Just might have seemed that way from the difference in angles from the first two pics.
Yep, your right. It was just the angles the pictures were at.
That looks menacing from behind...
fudleyd
New Member
I think it looks nice too man! A BIT wider might look nicer but I don't know if it would be worth it or not. 
Stock Mustangs could benefit from the use of spacers..
however spacers and their potential failures scare the hell out of me. I would never put them on my car even though I think my rear wheels do need to come out 1"
however spacers and their potential failures scare the hell out of me. I would never put them on my car even though I think my rear wheels do need to come out 1"
EPIK
Member
My 1/4" spacers are from MM & they are light as hell. I didnt need new studs either. I dont see how a 1/4" thin peice of metal is gonna cause some type of failure??? There is plenty of thread left & like I said the are super light. Its the cheap 1" spacers from pep boys with internal studs that might fail, but the eibach 1" spacers work fine as well. i know plenty of people that run them with zero problems. They dont weigh more than a few pounds & use strong studs.
Well it has to do with leverage really. The spacer is not fixed to the hub. Even though it's centered on the hub or lugs, it can still shift slightly. So by allowing the wheel to move puts stress on the lugs where the protrude from the hub. The further away from the hub the wheel is (by means of bigger spacer) the more stress on the base of the lug due to increased leverage with the longer moment arm. Typically people upgrade the studs not for lenght...but for stenght by using hardened studs
I'm an engineer....so this is the stupid stuff that runs through my head when i consider mods
I'm an engineer....so this is the stupid stuff that runs through my head when i consider mods
Why? Shouldnt you be thinking of trains?
four six
Member
Similar threads
