yuuup .i want to hit the road race track with a few car club members.willow springs and button willow.willow springs was Shelby's testing ground
i rolled the rear wheel lips and tacked them to the inner tubs,they came out nice. then i started on the butchered dash . there was a 1 inch hole to the left of the key switch that i filled . the radio open had been cut out . i had an old dash with a good radio opening so i cut out the piece that i...
i dropped the upper a arm mounting holes, 1 inch down and 1/8 inch back for 65-66 . simply one inch down for 67-70, you do not have to fill in the upper holes . start with a small bit so the holes don't wander off your mark then go to the larger bit . the a arm slides right in . there is a bit of flange around the holes inside the engine compartment that will have to be flattened so...
i rolled the lips on the front fenders today. started by getting a 1/8 inch wire cut to length and pre bent to fit inside the lip. i use the bench as the dolly it is soft wood and will not dent the radios of the wheel opening along with a moving blanket to soften the hammer...
i haven't had much time to work on it , but i did get it sanded down. i was looking at it the other day and noticed blisters and lines in the black coating and the weld through so i sanded a spot .i found that there was writing under the coating in either felt pen or grease pencil so the coating didn't stick. i sanded it off with a D A sander. this is realy...
i just could not stand it ,that dent had to go . i got out my stud welder ,another Harbor Freight goody. before you can say weld, it is welded .the tool i made from an old pop rivet gun .it pulls the metal up flush with the surrounding surface and stops. it took 6 studs and about 30 minutes and the dent was gone. a light brush with a file and it was almost perfect . no bondo will be needed. i hate bondo this thing works great on creases and dings but you need clean metal to weld .
this is the last of the welding ,the quarter window holes are filled in .i cut a patch of 18 gauge, formed it to fit and held it in place with a welders magnet.great for hands free work. i tacked all the corners first then about every half inch making sure the surfaces were flush all the way around and...
i am still waiting on red oxide primer ,because every thing i order has to take forever to get here, so i narrowed a 69 9 inch to 66 width. its pretty easy .just jig it up in the band saw so it cuts true, and then take the bearing retainer and ckuck it up in the lathe and cut it loose. two inches come off the 69 housing each side then the bearing retainer is cut down in the lathe to 1 inch and pressed back into the axle tubes with a...
my primer made it in to day.seems know one in my area uses red oxide so they don't keep it in stock.i will have to order a couple gallons and just tuck it away because i will be needing more. i will be sand blasting i hope, tuesday. then i will seal all the seams with 3M tan seam sealer,that will take at least 4 tubes .then i will fill the 4 panel joints and it will be ready to primer and remove from the rotisserie.
i got my sand ,15 bags .that should be enough. 5 gallons of gass for Leroy.
charged up his battery.i will be blasting first thing in the morning. every thing is locked and loaded and ready to go. i even bought a brand new face shield so i can see what i am doing.
i can't wait to see that ,love Guardsman blueVery cool, I am painting our 67 project in Guardsman Blue as well.
4 1/2 hours ,doesn't sound like a lot of time but try holding a 2 1/2 inch high pressure hose with 90 psi at the nozzle for 4 1/2 hours and see how you feel i am beat. every thing cleaned up real nice. but the engine compartment,was a PAIN IN DA BUTT!! some one painted it with some kind of rubberized painti like to never got it off. i used 5...
is it a silver ? i think that would look good on Guardsman blue
i got it primerd to day .i love this primer . it is about the stickiest stuff i have ever seen .couldn't hardly take a step in the paint booth,my shoes would stick to the floor. i sprayed the inside and outside first just encase it over sprayed,the out side will be sanded any way, it didn't. i sprayed the bottom last because it...
i picked up the brake ducts yesterday. i have to get a new 3 inch hole saw ,i want a nice clean cut hole. i thought i had a set of side scoops but i cant find them so i will have to order a new set. the flat bottom duct goes in the quarter scoop and just pop rivets in place ,on the inside of course. the curved pair go on the inner wheal tub from the inside and just pop rivet as well. i will seal them with...