• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Injector Help!

  • Thread starter Thread starter gcwh02
  • Start date Start date Jun 16, 2006

gcwh02

New Member
Jun 20, 2005
515
0
0
pottstown, PA
Jun 16, 2006
#1
  • Jun 16, 2006
  • #1
I'm putting in the new engine this week and debating on whether to get 30 or 36 lb injectors. Its all in the sig, 12:1 comp. 350 stroker. I hear that 30's will be more suitable for the street and it is a street car seeing some track time. But I have a feeling that I will not be getting enough fuel spinning high rpms. Any help will be appreciated, thanks.
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jun 17, 2006
#2
  • Jun 17, 2006
  • #2
I woudl say 36# inj depending on the total combo, rpm range and expected power. We've made over 430RWHP with a 30# inj when using a tuner so we can adjust all the fuel parameters.

Are you using a stock EEC?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jun 17, 2006
#3
  • Jun 17, 2006
  • #3
Injector HP ratings: divide flow rating by.5 and multiply the result by the number of injectors. This uses a 100% duty cycle. These ratings are for naturally aspirated engines. See my comments on pressurized induction in the paragraphs following this one.
Example:
19/.5 = 38, 38 x 8 = 304
24/.5 = 48, 48 x 8 = 384
30/.5 = 60, 60 x 8 = 480

The preferred duty cycle is about 85% maximum, so for a safety factor mulitply the final figure times .85.

Remember that the above ratings are at 39 PSI. Increasing the pressure will effectively increase the flow rating. Example: a 19 lb injector will flow 24 lbs at 63 PSI, and a 24 lb injector will flow 30 lbs at 63 PSI.
 

gcwh02

New Member
Jun 20, 2005
515
0
0
pottstown, PA
Jun 17, 2006
#4
  • Jun 17, 2006
  • #4
thanks a lot rick and jrichter, 30lbs it is. I don't see this combo going over 375 n/a
 

Grn92LX

Fidanza Man!
Founding Member
Jan 14, 2001
6,819
64
129
New York
Jun 17, 2006
#5
  • Jun 17, 2006
  • #5
I'd listen to what Rick says and go 36's. But you didn't even come close to listing enough info for anybody to help you.

You have a full point more compression than me and it sounds like you are spinning higher than me since you said high rpm's. I run 30's fwiw.
 
You must log in or register to reply here.

Similar threads

G
Need tuning help with 4100 Carburetor
  • Gary’s 67
  • Aug 18, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
252
1965 - 1973 Classic Mustangs -General/Talk- Aug 22, 2026
manicmechanic007
I
Engine Help requested in identifying how to resolve engine light issue
  • Ianslaney
  • Oct 4, 2026
  • SN95 4.6L Mustang Tech
Replies
1
Views
186
SN95 4.6L Mustang Tech Oct 4, 2026
Bullitt347
T
Drivetrain TREMEC TKX 1–2 Grinding Issue at ~4,000 Miles + Poor Warranty/Customer Service Experience
  • Ttopfoxguy
  • Oct 10, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
339
Fox 5.0 Mustang Tech Oct 15, 2026
JMG9350
J
9
Forced Induction Prepping for supercharger on non-stock build
  • 91fox427
  • Nov 25, 2025
  • Fox 5.0 Mustang Tech
Replies
7
Views
606
Fox 5.0 Mustang Tech Jan 5, 2026
Qtrhrse23
C
Dyno day! # guesses?
  • clayton seiders
  • Aug 15, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
15
Views
657
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 16, 2025
Scrapla347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?