Injectors

91ghp5.0

Active Member
May 25, 2005
42
0
28
Somewhere
I know this is a totally noob question, but i've always had a misunderstanding on this question. do injectors constantly pump in the amount of gas they are rated at? i wouldnt imagine so, but i was told this was the case once. they ramp up their injection as the computer tells it too (according to boost, etc.), correct? thanks in advance!
 
The computer applies the right amount of voltage to make them flow a certain amount and the rating is their maximum. You have to get a MAF or computer that is scaled to the injector you are using because if you don't and you are using a larger injector than the MAF/comp thinks you are, you will be flowing more fuel at any given voltage which will cause a rich condition all the time and a bad running/bad mileage vehicle.
 
91ghp5.0 said:
thanks! just wanted a bit of clarification. so if i had a turbo/SC car (or any reason for larger injectors), i could get decent mileage if i kept my foot out of it? thanks again!

The injectors are not going to be the cause of poor mileage, but if you have a need for them, then chances are you're not going to be worried about getting good mileage.

Oh and to clarify a bit. They are rated at the max duty cycle for a stock pressure of 38-40 psi. If you increase the fuel pressure, 19 lb/hr injectors will flow more than 19 lb/hr.

Chris
 
Injector HP ratings: divide flow rating by.5 and multiply the result by the number of injectors. This uses a 100% duty cycle.
Example:
19/.5 = 38, 38 x 8 = 304
24/.5 = 48, 48 x 8 = 384
30/.5 = 60, 60 x 8 = 480

The preferred duty cycle is about 85% maximum, so for a safety factor mulitply the final figure times .85.

Remember that the above ratings are at 39 PSI. Increasing the pressure will effectively increase the flow rating. Example: a 19 lb injector will flow 24 lbs at 63 PSI, and a 24 lb injector will flow 30 lbs at 63 PSI.


Here's where I will lose some of you for lack of understanding:

Increasing the intake manifold pressure above atmosphereic decreases the flow rating by the amount of pressure increase.
Example: injector flows 30 lbs at 39 PSI. You have 10 PSI boost, subtract the 10 PSI boost from the 39 PSI fuel pressure. That means you have 29 PSI pressure at the injector tip. Therefore, a 30 lb injector flows 25 lbs with 39 PSI base fuel pressure and 10 PSI of boost.

Fortunately, the design of the fuel pressure regulator causes pressure to increase as manifold pressure increases. The increase may not be linear though.

See http://users.erols.com/srweiss/ to get the calculators used in these examples.
 
Thanks for the info about boost. Most turbo and blower kits are set up to compensate for the boost with a FMU.

Fortunately, he's not running any boost.

Still, your multiplier isn't too far off from the range ford uses [13.6 (85% duty cycle) vs. 11.84 (74% duty cycle)].

I think it supports the reccomendation for 30 lb injectors.

30 lb injectors: 480 hp * .85 (duty cycle) * .85 (driveline loss) = 347 rwhp.

24 lb injectors: 384 * .85 * .85 = 277 rwhp

Chris
 
Mr. Potato Head said:
The computer applies the right amount of voltage to make them flow a certain amount and the rating is their maximum. You have to get a MAF or computer that is scaled to the injector you are using because if you don't and you are using a larger injector than the MAF/comp thinks you are, you will be flowing more fuel at any given voltage which will cause a rich condition all the time and a bad running/bad mileage vehicle.


Im pretty sure it doesnt vary the voltage to make them flow a certain amount....It uses 12 volts all the time and the computer increases the injector pulsewidth (how long the injector is energized or opened) to allow more fuel to spray in. Just FYI :nice: