Build Thread Mustang5L5's Build Thread -

Mustang5L5 · Oct 27, 2021

Ok. Got around to removing the support bar on the radiator and straightening out the main rib. I had a plan to reinforce it if necessary, but it wasn’t needed. There was no flex. Radiator mounted up perfectly.

Dropped in the car and all the coolant hoses installed. Still need to wire it up, but I’m very happy with this setup.

My Chase Bays coolant bottle is in the mail. I think I have a good spot to mount it. Time to grab some coolant from local parts store.

Edit: also, used the LMR radiator hold-down vs the stock clamps. I like it. I think the hood prop will interfere with it but I’m pretty sure I’m going with hood struts instead

WhiteCobra95 · Oct 28, 2021

This is a fun build to watch. It's like how the Fox Body should have come from the factory. Awesome work!

Mustang5L5 · Oct 29, 2021

Ok. Buttoned up some loose ends. Checking wiring, set the dist to tdc#1 and started filling with coolant. My overflow bottle isn’t here yet but I can just use a water bottle for now. Fans aren’t wired but I don’t plan on running it that long.

Need to grab some distilled water in the AM….but I think I’m ready to start it up.

Unfortunately it’s going to rain tomorrow. I want to start it outside in the driveway vs in the garage. You know…in case it catches on fire or something

I’m nervous. Lot of work to get to this point.

Mustang5L5 · Oct 30, 2021

Rigged up a temp overflow bottle. Still triple checking. Just remembered I need to set the fuel pressure still. Last thing to do.

Miserable rainy day outside….so first start on hold

Mustang5L5 · Oct 30, 2021

Fuel pressure good to go. F it. Let’s fire this pig up

Mustang5L5 · Oct 30, 2021

Runs like I never even took it apart

View: https://youtu.be/qPuslshajnI

View: https://youtu.be/xTkOYVdhnH4

WindsorPenchant · Oct 30, 2021

Let's go!! Congrats on one clean beast!

Mustang5L5 · Oct 30, 2021

One more

View: https://youtu.be/Tv0VPBF5z4M

derek1993 · Oct 30, 2021

Mustang5L5 said:
One more

View: https://youtu.be/Tv0VPBF5z4M

SWEEET!!! Congrats on an amazing build!!

Mustang5L5 · Oct 31, 2021

Ok back to work.

Started it a few more times without issue. Set the idle screw. Was going to set the timing but really need to make sure the radiator is full to avoid overheating.

So here’s the issue. Seems there is an air bubble I cannot burst. Car is getting up to temp but it does not appear coolant is flowing. Upper hose is cold and feels like there is air inside as there is no resistance when I squeeze it. Lines to heater core are warm, but when I put the heat on it cools off rather fast. I’ve tried 3-4 different cycles and still can’t get the radiator to start moving coolant through it

I put 2.75 gallons in so far. Capacity is 3.5 gallons. I have roughly 1.25 gallons of air I need to purge out somehow.

I have an idea.

This line was mostly meant to be temporary. However it’s full of air and also the highest point on the engine. If I use a vacuum pump here (with liquid separator in line of course) and fill the overflow with coolant, I should be able to suck the air out while drawing coolant in from the overflow. Might not fill it up all the way, but should displace enoigh air to start to get some coolant moving?

Also, she moved on her own power for the first time in 2 years 2 months today.

FortySix&2 · Oct 31, 2021

Lol, ARP 12 point bolt for a hose plug. The Mustang5L5 way.

02 281 GT · Oct 31, 2021

FortySix&2 said:
Lol, ARP 12 point bolt for a hose plug. The Mustang5L5 way.

Was just about to say the same thing.

KRUISR · Oct 31, 2021

How about just pull that bolt out, prop it up higher than the rad and keep filling the rad until all your air is out of the system.

Better yet, replace with a clear hose (temporarily) so you can see that the coolant has burped at least to that point. Then plug the hose and go through a engine running cycle.

Monkeybutt2000 · Oct 31, 2021

I'm surprised you don't have a no-spill funnel. Works everytime.

Mustang5L5 · Oct 31, 2021

KRUISR said:
How about just pull that bolt out, prop it up higher than the rad and keep filling the rad until all your air is out of the system.

Better yet, replace with a clear hose (temporarily) so you can see that the coolant has burped at least to that point. Then plug the hose and go through a engine running cycle.

Tried a version of that. Didn’t work. It’s like there’s an air pocket which won’t move.

Gave up for the day (although I didn’t try much) to get ready to take the kiddos out for Halloween.

Prob won’t be able to start it up until next weekend as my typical wrenching time is after 9pm. The car is pretty damn loud now. Definitely doing to ditch the flows for the Borlas to quiet it down a tad.

I’ll likely start putting the rest of the ac hoses on and pull a vacuum on the system, and work on fan wiring.

I was tempted to drive it up the street and back but I don’t want to do that until I at least have coolant circulating

Definite smile on my face each time I start it up

Mustang5L5 · Oct 31, 2021

Was able to get another 1/4+ gallon in this way. This pipe was empty. A little squeezing of hoses burped some more air into radiator.

Unfortunately no time to fire up and warm up to see if coolant starts flowing. Will need to wait to see

95BlueStallion · Oct 31, 2021

Man, I was just thinking that I liked how it sounds! Congrats and a successful first start.

Mustang5L5 · Oct 31, 2021

I love how it sounds. It’s just loud!

If I was 20 I’d be all over it but I’m turning into an old fart. I’d kinda like to cut it down to….half.

I also think the Borla are straight thru mufflers so they may even give me some HP.

Boostedpimp · Oct 31, 2021

LMR offers a heater tube that doesn't have that coolant port for the egr if you didn't want to deal with blazing it over but it also looks like you maybe keeping it since your actually using it in the pictures

Fox Body Mustang Heater Tube & Hose Kit Without Coolant Tube| (86-93)

Replace the crucial components of your 1986-1993 Mustang's heater system with 5.0 Resto's heater tube and hose kit w/o coolant tube!

lmr.com

Mustang5L5 · Nov 1, 2021

Not really using it but more like a temp solution. One day in the future I’ll likely address it for a cleaner solution with the tube without the nipple.

Right now, it’s low on the priority list

Build Thread Mustang5L5's Build Thread -

Mustang5L5

That is…until I whipped out my Bissell

WhiteCobra95

Mustang5L5

That is…until I whipped out my Bissell

Mustang5L5

That is…until I whipped out my Bissell

Mustang5L5

That is…until I whipped out my Bissell

Mustang5L5

That is…until I whipped out my Bissell

WindsorPenchant

Active Member

Mustang5L5

That is…until I whipped out my Bissell

derek1993

Active Member

Mustang5L5

That is…until I whipped out my Bissell

FortySix&2

Active Member

02 281 GT

Agreed...My wife has great Boobs

KRUISR

Monkeybutt2000

Mustang Master

Mustang5L5

That is…until I whipped out my Bissell

Mustang5L5

That is…until I whipped out my Bissell

95BlueStallion

My assy trans to myself

Mustang5L5

That is…until I whipped out my Bissell

Boostedpimp

Fox Body Mustang Heater Tube & Hose Kit Without Coolant Tube| (86-93)

Mustang5L5

That is…until I whipped out my Bissell

Similar threads

Build Thread Mustang5L5's Build Thread -

That is…until I whipped out my Bissell

That is…until I whipped out my Bissell

That is…until I whipped out my Bissell

That is…until I whipped out my Bissell

That is…until I whipped out my Bissell

Active Member

That is…until I whipped out my Bissell

Active Member

That is…until I whipped out my Bissell

Active Member

Agreed...My wife has great Boobs

Mustang Master

That is…until I whipped out my Bissell

That is…until I whipped out my Bissell

My assy trans to myself

That is…until I whipped out my Bissell

That is…until I whipped out my Bissell

Similar threads

Privacy & Transparency

Privacy & Transparency