Fox Sticky throttle

Dontknowchit · Mar 24, 2024

I've got a sticky throttle cable and I know that it's not an abnormal replacement part that I should be able to find on LMR but I was wondering, with everything else on my new to me car terribly sticky and needing cleaned and degummed, has anyone ever has success lubeing up the throttle cable?

It seems to want to stick at about 1500 rpm when coming to a stop light after a long cruise and I have to use my foot to pull back on the pedal to free it. It also makes it difficult to not overrev when taking off from first as it wants to stick closed. Does not seem to stick at wot.

Anyway, anyone have luck just shooting lube down the sheath?

limp · Mar 24, 2024

Are you sure its the throttle cable? I see alot of this on " Just Rolled In " and its the floor mat impeding the throttle pedal.....

If you have a solvent tank, I would soak the cable in it all day, while occasionally working it by hand..
if you get it working Ok, try lubing it with some motorcycle cable lube.... work it some more and see what happens...

Dontknowchit · Mar 24, 2024

Thank you. It certianly seems like the cable, I tried to spray some lube on the spring and cleaned out the butterfly valve so I do not think it is that anymore, still doing it. I do not have floor mats in it yet so can't be that. Thinking if I already have the cable out to lube it might as well replace it. I don't really see any obvious way to get any lube down the sheath from the motor side and from the car side I'm fighting gravity. May just add it to the replacement part list.

General karthief · Mar 25, 2024

Man, if you can make the factory cable or find another factory cable I'd do that before putting an aftermarket one in.
Disconnect both ends and test the smoothness, I had an issue with my peddle.

Mustang5L5 · Mar 25, 2024

Disconnect the cable and straighten it out in the engine bay. Can you easily articulate it?

I'd try to correct the issue with your current cable or find another good used cable off ebay before going with an aftermarket cable. The cable LMR carries is the same as you'll find on Amazon or local parts store. It's plastic and cheap and not very good.

86HO5.0 · Mar 25, 2024

Have you cleaned the TB? Throttle stop screw too far out?

AeroCoupe · Mar 25, 2024

Or you can just make a new one. I did this a while back and posted how to do it over on the Corral. If need be I can post it here as well as we all know how stuff disappears.

https://www.corral.net/threads/1993-5-0-injected-throttle-cable-replacement-with-lokar-cable-this-is-a-long-post-with-lots-of-pictures.2514984/

FastDriver · Mar 25, 2024

Just gonna throw this out there... maybe dumb, but is anything in the pedal assembly binding or otherwise impeding the functionality of the throttle? Just an idea.

Dontknowchit · Mar 25, 2024

86HO5.0 said:
Have you cleaned the TB? Throttle stop screw too far out?

I did clean the tb with Berrymans and lubed the spring, screw, and everything else in the path of the wd spraycan. The idle screw is all the way out, but that was how I had to adjust it to get idle right during retiring and Base idle reset. Is there a "too far"? I thought you backed it out as far as possible while it stayed running?

Dontknowchit · Mar 25, 2024

FastDriver said:
Just gonna throw this out there... maybe dumb, but is anything in the pedal assembly binding or otherwise impeding the functionality of the throttle? Just an idea.

I also feel this "sticking" when attempting to open the throttle blade manually at the tb. It seems to snap shut and be difficult to push back open occasionally. I suppose the pedal could be binding up. I can attempt to lube the pivoting linkages to see if that helps.

Dontknowchit · Mar 25, 2024

Mustang5L5 said:
Disconnect the cable and straighten it out in the engine bay. Can you easily articulate it?

I'd try to correct the issue with your current cable or find another good used cable off ebay before going with an aftermarket cable. The cable LMR carries is the same as you'll find on Amazon or local parts store. It's plastic and cheap and not very good.

Well that's disappointing

limp · Mar 26, 2024

If you look at the pic of the lube I attached, there is a metal tube on the left side of the bottle ( that screws on the top) that is very tiny and will get inside between the cable and housing while you squeeze the lube...
Have you disconnected the cable from the carb?? then worked the carb linkage and the cable separately, trying to diagnose each one??
Have you worked on the carb recently? Could one of the blades be contacting the carb to intake gasket??

AeroCoupe · Mar 26, 2024

No carb on this one Limp.

86HO5.0 · Mar 26, 2024

If the screw is all the way out, are you sure the TB butterfly isn't 'catching' on the TB?

Are the edges of the butterfly clean?

limp · Mar 26, 2024

AeroCoupe said:
No carb on this one Limp.

LOL... PUlled the Gray Hair card on that... I confused it with another post...

General karthief · Mar 26, 2024

it's likely the blade will stick if the adjustment screw does not land against the stop,

Dontknowchit · Mar 27, 2024

Solved!
Well at least I know the issue. The idle screw was not making contact with the stop tab on the TB. As I rotated the screw in, it got very very tight, then "twang/snap" and it was easy to turn again. The TB spring has some sort of "catch" on it if allowed to rotate too far back, or snap back hard without being controlled by the stop tab and screw it kind of over rotates and binds when coming off that position. Feels just like the throttle blade is stuck when manipulating by hand but it is definitely the spring. After opening it all the way and letting it snap back at full speed about 1500 times, I think I found the sweetspot for having it backed out but still stopping it before the spring gets bound up on itself. I guess it has to have a little preload on the spring to take the slack out of it before it actually opens the blade. I'm sure my idle will be higher now, but have to check tomorrow as too late and loud to mess with it more tonight.

But what is this thing? This greasy stamped metal disc was wedged behind the throttle pedal bar. Does it serve a purpose?

Dontknowchit · Mar 27, 2024

Mustang5L5 · Mar 28, 2024

That’s kinda what locks the throttle cable into the firewall. It clips onto the cable from inside. Trying to find a pic

General karthief · Mar 28, 2024

Kinda looks like a slotted disc washer from a 59 Hennway, very rare

Fox Sticky throttle

Active Member

wrap a little cheese around it and its a done

Active Member

wonder how much it would cost to ship you a pair

That is…until I whipped out my Bissell

Active Member

lube between the nut and the face. I know my lubes

I was uncomfortably high & wearing a helmet

Active Member

Active Member

Active Member

wrap a little cheese around it and its a done

lube between the nut and the face. I know my lubes

Active Member

wrap a little cheese around it and its a done

wonder how much it would cost to ship you a pair

Active Member

Active Member

That is…until I whipped out my Bissell

wonder how much it would cost to ship you a pair

Similar threads

Privacy & Transparency

Privacy & Transparency