Hey all, so iv been battleing with my beast for a good few months on this issue. Its gets hot after driving for about an Hour. About 3 months ago i did head gaskets thinking that was the problem, and its been off and on with it getting hot. I drive nice and easy, minding my loud pedal and its...
Might sound like a dumb question but what exactly is the difference between a catback exhaust vs axle back? I have ford performance mufflers on now (axle back) and I think it sounds decent. I want to move up to Borla Atak cat back.
Now I know the actual mufflers will be much smaller and less...
Up for sale from my shop, Tods Hot Rods located in Moorpark CA 93021, are the remaining suspension related parts removed, degreased , clean and prime and painted in some instances from a 2000 GT convertible 4.6 5 SP parts donor car that was in my shop. I used the tremec, the BBK intake the rims...
Hey all -
Tried to search many forums and cannot find a solution. I have a 96 cobra that has low compression on all cylinders. However - a leakdown test was performed, and each cylinder seals like it should when the crank is turned manually. Which has me guessing it’s a timing issue? I’ve seen...
Selling this used but freshly(11/21) machined Manley 190350 crank.
I purchased it with the intent of building a shortblock for my boosted 2v. Decided to switch platforms and sell my car so I no longer need it.
Machine work was done by Ohio Crankshaft for the previous owner.
Asking $550 OBO...
I have a stock 2002 4.6 Cobra. Wondering if and intake spacer would help much at all or a larger than stock throttle body (70 or 72 or 75 or 77...) would add much...or both?
Should I look toward a different than stock intake manifold?
Reprogrammed chip or programmable chip or ECU?
Headers...
I have a 2002 Mustang Gt with comp cams 270 and a few other bolt ons. Whenever i start the car it idles and drives fine, until the fan comes on. If the car is sitting and idling and the fan kicks on for temperature, it’ll instantly kill the motor. If I’m driving and the fan is on and i come to a...
Hey all, there is a guy locally selling one of the older Ford SVO Superchargers, which I believe are based on the M112.
It's supposedly modified to work with PI. Is this worth looking into? Anyone on here had/have one? I've been wanting to do a power adder for a couple years now and this seems...
Does this look like a ground? 2003 mustang GT. Replaced intake and now reverse lights,speedo, and blower motor is out. Could this have something to do with it? The wire is only about 5-6 inches long and literally nowhere to plug up. Any ideas?
I had just finished replacing the TB, pilot bearing, rear main seal, clutch, etc. On my 96 cobra because of a knocking sound whenever the clutch pedal was all the way out. After about 30-40 mins of driving to test it out, the same exact knocking sound is back. Im pretty sure I replaced it...
I own a 96 Cobra, and I am having huge trouble with the hoses coming from the CAI to the valve cover, and the hose from the CAI to the IAC. The one going to the valve cover doesnt fit properly causing a vacuum leak, and I cant find the hose anywhere!! Its like it doesnt exist. Then the second...
So im having a problem with the pcv valve hoses not properly fitting and I cant find the proper hoses anywhere. I want to just delete the hoses altogether can anybody provide some instructions on how to do that?? I can only find posts on the 03-04 cobras. Im pretty new to working on cars so Im...
Hi all. This is my first post to the forum. I did try searching for old posts to answer my question.. But could not find anything after a few minutes.
I purchased a turbo kit for my 2006 Mustang GT. I would like to go the Megasquirt route for tuning if possible. I have a friend who does MS...
I recently purchased a 96 mustang cobra and the car was overheating so I flushed and replaced the coolant, but no help. Every time I drive the car for about 20 mins the engine bay smokes and theres hot coolant leaking from the reservoir. After some research, I am going to replace the thermostat...
I recently purchased a 96 mustang cobra and I noticed that my coolant crossover tube is very rusty on the outside as well as inside. Its very hard to find a crossover tube replacement so Ive been looking at a delete kit instead. A bit pricey, but my question is I see all these kits change the t...
I've been hunting for the most cost effective plenum option for a 2v. My major concern was that I'd like to not spend the money on an aftermarket plenum for a Pi/stock intake manifold as I will be using a Victor Jr in the future and I refuse to choke out the 4150 flange with a mmr adapter...
So I plan on putting the On3 turbo on my gt and I am trying to get 400hp on it. I was wondering what parts I would need to get or that would be smart to get. I already know that the stock rods and pistons tend to go out around 400-450hp and I plan on buying them but I don't know what sizing...
Hello everyone,
Yes, I am aware there are plenty of other posts regarding this. Just want some specific info without looking 20 places if anyone can help.
I have a 4.0 that's getting close to 200k on it, and shortly after purchasing it, it developed transmission issues. So I am just going to...