hi guys. Ive read countless forums but never been part of a group before. WELL, ITS TIME! I have everything from an 03 terminator and want to put it into my 66 Fairlane. My questions are;
1) who is a good one for a wiring harness for that thing? 2) what are some good options for fuel systems...
Hi everyone,
I'm around Ewing, NJ, and am looking to sell my 1994 cobra, I'm the 3rd owner and have had the car since 2004, putting about 70k miles on it in total, mostly as daily driver. Asking $5,000 obo. I stopped driving this car regularly after June 2018, but kept up with weekly start-ups...
I need a good picture of 1978 king cobra wheel center cap the original snake. Just the snake close up. I am attempting to get some made, any help would be great.
The ones I have are bad.
Thanks
Can't seem to find the correct pads for the calipers I have. They are supposed to be for a 2003 Cobra. PBR Castings part #K247-047C
2 Different sets of pads 2 different brands and neither Brands fit! The Spring clips are spaced too wide apart and they don't fit inside the pistons.
One set are...
I want to to put as wide of a rim and tire I can on my 1998 Mustang Cobra without making any serious mods to the suspension except I do want to drop it 2”s.
I want the car as low as I can and I want the tires to be as wide as I can fit in the wheel wells and not have the rear wheels and tires...
Hey guys, as the title says, I’m considering swapping a 1996 Cobra engine with its matching harness, T56 transmission, gauge cluster, rad and fans, and stock exhaust manifolds into my current car, a 2004 3.8L with the T5. I will also be swapping my 7.5 to an 8.8. I was wondering if anyone has...
Hi all. First post in a long time. Just bought a 1996 Mystic Cobra after 4 years of not having a Stang. This is my 8th Mustang and i think it might be a keeper.
Anyway, one of the things I would like to change are the seats. I'm pretty tall and have always found that the seats in the SN95s...
Just picked up this 93 Cobra with a '13 BOSS 302 coyote swapped in. I currently own a '00 ranger that I swapped a HO 302 from a 01 explorer with a t5, and a 01 explorer.
I have a 2003 Mach 1 that just rolled 167000. It leaks oil, has a little tick or rattle and it starting to show it's age. My question is, where can I find a new 4 valve 4.6 long block or short block. Everywhere I look it's all coyote stuff. I understand the coyote is a great motor, and I'd...
Hello every one. Just bought a 2001 Cobra. Car needs a clutch. I already bought an Excedy Stage 2 and an SLP loudmouth 2 exhaust. While I have the transmission out what else should I do to the car at the same time? Any suggestions? Tranny mounts? Etc....
Figure while I’m dropping the cats and...
I somewhat recently purchased a cobra upper and lower and will soon get around to installing them. As my car is a daily driver I am trying to sort out any issues beforehand. I know this is a common swap so I'm sure some of the information I'm asking for is out there I'd just like to be certain...
I recently bought a 2001 Cobra and I noticed when the car is fully stopped and you try to shift into 1st gear, it grinds occasionally, even with the clutch pressed all the way in. Any ideas on what it might be and what I can do?
2003 Cobra Convertible
Redfire Exterior Color
Black cloth top
Black interior with Gray insert (Alacantara) and leather
68k Miles
Price is $21,500
Located in Hoover, AL
Built May 27th 2003 and is 3938 of 5082 and about 611 in this combination
Original Purchase was at Eckenrod Ford, Cullman AL
I...
Weld wheels 17x9's front 17x10's rear, brand new tires 245/40/17's 315/35/17's RARE wheels never seen weather $1800 859-816-7743 not on here much so texting is the best way to reach me
5x114.3 also has other 5 lug holes (was on gto)
Burlington ky
Mustang
Cobra
Gto
Corvette
Lexus
Supra
I have a couple issues going on with my Mach 1 at the moment. For one i recently replaced my drivers side window motor since it went out but now when ever I raise it all the way up or drop it all the way down the motor doesn't stop and make a loud clicking sound of the 2 gears clashing unless I...
I will update this resource shortly as a step-by-step process. Link above is a direct download to a .zip file that includes the measurements for cutting out the pieces needed to fabricate the IRS hardtail mount and the process pictures of how to fabricate the mount. There are other ways to do...
I need some guidance on removing the lower nut securing the master cylinder to the hydroboost. I have searched online but found nothing. The space is so small and I can barely get a hand between the valvecover and master cylinder using the smallest socket wrench I have. I've also tried to go...