engine

  1. PakstinN

    Buying An Ed Curtis Cam

    So for Christmas my parents told me they would by a custom camshaft for me to help me complete my 306. I would like to begin the process of getting this cam but I’m not sure how to get ahold of ed Curtis to give him all the details of my setup. I believe I found where to buy them but I’m not...
  2. PakstinN

    Engine Ported Gt40p's??

    Hey boys, a short while ago I had the misfortune of snapping the crank in my gt40p headed 302 (how/why it snapped I have no idea) so I am currently going through the rebuilding process to get her back on the road..I already have a shortblock all done up and ready to go..HOWEVER, when the crank...
  3. MCM Tees

    Mustang Ii / Ranger Tranny

    I want to convert my 74 Mustang II from an automatic to a manual. Only problem is the cars engine was replaced with an 83 ranger 2.8V6. I prefer a 5 speed but will settle for a 4 speed. Does anyone have any suggestions i.e. transmission numbers that will fit the block?
  4. M

    Engine Oil, Smoke, Fire And Brimstone.

    Ok, not really the last two. Vehicle Information: 1993 5.0 litre in a 1990 Fox, A9L running GUFB strat on unknown def, aftermarket tb but not aftermarket MAF, knockoff cobra intake I think and possibly stock injectors. Hope this isn't the wrong board, suck at forums. I'll move it if needed...
  5. Buddha_DUT

    Engine An Engineering Question On Improved Torque

    So I know that everyone loves to watch your engine twist when you hit that gas. It just speaks raw power. But when I look at that I see potentially wasted torque. Is there a concrete reason why someone couldn't brace your engine and tranny so that they can't twist and flex so that all of that...
  6. B

    My Mustang Motor Swap

    Hello. Am I able to swap out my blown 1997' 3.8l engine (with high miles), with the motor of 1995' 3.8l? And if so, then what exactly needs to be done with my 1997's original computer so that it recognizes and is compatible with a 1995 engine? I appreciate any attention given to my question...
  7. 0

    Exhaust 2000 Gt Rattle

    I have a 2000 Mustang GT 5 speed. It has longs tubes and an O/R H-pipe. When RPMs are falling between 1500-1000 there is a loud rattle coming from under the car somewhere from the front wheel well to the seats. It sounds as if I'm taking a hammer and beating two pieces of metal rapidly. As soon...
  8. C

    Engine Shops In Wa State

    Ok ladies and gentlemen. I was trying to get whole of Dave Bliss to do some motor work on my wife's 67, but it appears he may of retired? Anybody know of a reputable guy around the Seattle-Tacoma area to do some machine and engine work? Thanks in advance....
  9. D

    Please Help Identify Engine Parts Of '99 Gt

    Hi All, I ran into the common issue of the original all-plastic intake manifold breaking, and need to have it replaced. Given that my car is more than 17 years old, I decided to replace all hoses and gaskets that need to be touched during the process. I’m Hungarian, I don’t know the English...
  10. D

    Can I Use S550 Exhaust Cams In 11-14?

    Hi all, I've got a new crate engine in my 2011 Coyote. It's got the 2015 cams/Phasers/chains etc. I've been told I need to change back to 11-14 VCT for the engine to run properly. I keep getting bank 1 and 2 intake cams over retarded codes. I've heard that the S550 exhaust cams can be used...
  11. M

    E85

    Those who have done it tell me all about it. Did you upgrade anything other than injectors? Power gains? Did it actually eat through anything? A safer e70 tune worth it? There's tons of rumors out there that are just rumors. Hoping to get real experience an even some tuners words of wisdom if...
  12. F

    Engine Oil Leak Only When Engine's Cold

    So I recently purchased a 1990 Mustang GT, so far it doesn't leak anything beside a little power steering fluid (or radiator fluid I'm not sure). Anyways it leaks a little bit of oil from where the oil pan meets the bellhousing. The weird part is that it only leaks when the engine is cold, It...
  13. H

    Engine Head Gaskets Again

    Alright guys long time no post. Last time I posted I was fishing out a bolt from the dizzy hole thanks to my brother. So a little recap of what I've been dealing with Blew my head gaskets. Bought new heads. Lower intake wasn't on right. Than dropped bolt down dizzy. So I got my car back...
  14. Shelden

    Cracked Exhaust Manifold

    Going to be removing my passenger side exhaust manifold due to it being cracked completely in half right above where the flange connection is, managed to remove the 6 nuts fastening the manifold to the block , and the top egr bolt, but I can't seem to reach the lower egr bolt or the two bolts...
  15. M

    Water On Pistons How To Remove?

    Nevermind. I think I got it.
  16. chapters707

    Engine Carbon Or Oil Deposits On Block?

    Hello all, I am in the midst of replacing my 4.6 motor on my 96 with a new one I purchased online. (The new one isn't off a '96, it was manufactured in '99 and doesn't have pi heads so I'm thinking it might be off an explorer or something.)I have the old one pulled and am preparing the new one...
  17. M

    Expired 2014 F150 Coyote Engine

    I bought this engine from a friend who totaled their 2014 F150 with 15,000 miles. Truck was rear ended. Was going to use for my 1967 mustang coupe. I am realizing how expensive the swap is going to be so thinking about selling. Motor is almost brand new and has everything except throttle body...
    • Motogil
    • Thread
    • 1965 1966 1967 1968 coyote engine f150 mustang 5.0 swap
    • Replies: 0
    • Forum: Other Classifieds
  18. M

    '91 Mustang - Lower Radiator Hose Burst Driving Up Steep Hills

    Driving up one windy continous HILL... my Fox body SLUGGED up to the peak of the hill. Pedal to the floor, moving to the top speed of 5 MPH...the LOWER RADIATOR HOSE BURST!!! Rusty brown water and coolant SPRAYED the entire engine bay. Now that I replaced the hose, slight coolant flush, NEW...
    • M36nace
    • Thread
    • 1991 1992 clean engine engine bay fox body mustang foxbody hose lower radiator
    • Replies: 4
    • Forum: 2.3L (N/A & Turbo) Tech
  19. Russell P

    2004 3.9 V6 Bad Engine Vibration

    I have been having some engine vibration for about a week now and I can't seem to figure it out. The whole engine shakes in idle and throughout the rpms (though it is worse around 1200 rpm). It also has a cough coming out of the back right tailpipe. There is also a rapid clicking type noise...
  20. C

    Gt Engine Rattle

    Hello, my name is caden, my account is new, but i have been surfing these forums for help with a constant, but unprogressive problem i have had with my 2005 mustang GT with just over 90k miles. The issue is a rattle coming from the front passenger side of the engine. I am absolutely certain it...
Top Bottom
Back
Forums
Menu