Price: $44,900 OBO
Location: Nampa, Idaho
View: https://imgur.com/a/1993-svt-cobra-88k-miles-Odxkjut
Helping my family sell their 1993 SVT Cobra. This is a genuine Cobra, not a clone. The car has been in the same family since new and includes the original window sticker and original dealer...
Hi all, I’ve been chasing heat problems for a while now. About 9 months ago I swapped gt-40s and a cobra manifold onto my 5.0 with an Anderson cam. The problem arose after this swap. When the car heat soaks coolant temps can get all the way to 220f, and Intake Air Temps up to 180f. I have a...
I have an 88 LX. My headlights and blinkers work but I have no hazard lights. The hazard switch connector is new, as well as the flasher and the fuses are all good. I also have zero dash illumination. I’ve changed the dinner switch, headlight switch connector, even the bulbs inside the...
I have a set of factory metal rear slats with the glass that has the little tabs from the factory so 'plug and play swap, a guy contacted me wanting to buy them, I'm not really gonna sell them (unless it's 'stupid money', what do y'all think they are worth?
They do need repainting..
I have a 91 mustang gt hatchback. I hate to sellit but I just don’t drive it or need it at this point in life. It’s a factory all black interior car with no REAL wear on it. It looks 20 to 15 years younger than it is inside! I’m not sure of the mileage on the motor but it has been swapped due to...
How rare is it really for a silver convertible nowadays? Back when they came out I know they weren't unusual but mine is the only silver CONVERTIBLE that I've seen. Unfortunately the top has been replaced so Randy, as named by the previous owners, has a cheap plastic back window instead of the...
Greetings ladies and gentlemen, it’s been too long!
I was watching this video of Matt Farah’s car and he mentioned that the Ford Performance crate engine he had in it was making 350 HP with a mild cam, Mac headers, a set of GT40X cylinder heads, and an explorer intake. I looked on Ford’s...
$1000 for the both
Greetings,
I have decided to go a different route on my 408W and have decided to offer for sale my intake manifold. I have been sitting on this thing for quite some time. I will not be separating the upper and lower. Please DO NOT contact me asking me to do this. I know...
I built this car 20 years ago with intentions to auto cross but I paused it to start a family.
302 bored 0.040 over Kieth Black pistons,
Ported Twisted wedge heads and Cobra intake, 24lb injectors, ECM Chip
E303 Cam, electric water pump, dual fans (needs to be finished) MSD 6AL ignition...
I’m looking for ideas on what type of steering wheel to get. I’d like to find one that will fit in my 88 Fox that has radio controls. Newer cars have way nicer wheels aesthetically and feel. There might not be anything that I can use that has radio controls already built in. I can figure out the...
I have a 1990 Mustang LX 5.0 | All motor component is stock besides having a mild cam.
When I am installing the intakes and cylinder heads, I want to know which part will be a bottleneck and which is fine. I also want a clear instruction on how to removing the stock intake and heads.
No idea where to list them at so I'll start this thread here until I get an idea of a good asking price. So, what are these worth?
I'm in vicinity of Fort Bragg/Liberty, NC.
Driver's Seat:
Passenger Seat:
Note - I have rewelded and painted where one side of one of the brackets...
So I have been thinking about getting a Fox Body Mustang and like the rear end of the Notchback more then the hatchback but I prefer the GT Front End As I like how clean it is. What are the requirements for changing the front end? Is it a straight Bolt-On? Does It require any fabrication?
I’m having problems with getting my new 87 5.0 lx to run properly and as well as when trying to start it I have to loosen the distributor and turn the timing up and down while the car is cranking to get it to start, once it does start and I set the timing to 10 degrees btc it’s runs good till it...
hi . i have a 89 gt and my tachometer needle go down when i start the car. sometime she start bouncing but she don't react to my idle .
when a stop the car she return to is place .i refresh the weld behind the tachometer and i clean all the contact behing the cluster.
last years the needle was...
93 LX coupe.
I Daily drove it for a couple years before it went into paint. Nice car.
2.3L out of an SVO Mustang. Mild mods to a fully rebuilt stock engine (BNIB Ford replacement 020 pistons, etc). Has roughly 11,000 mi on the rebuild. Runs great.
5 speed manual. It is actually a V6...