intake

Will the BBK 65mm gasket fit this TB? Don't really wanna remove the studs yet, feel like they'll break easily.

webers

What the value of a used Fox (not SN95) Ford Racing Cobra intake? Its one of the China-made ones but does have the larger oil baffle underneath.

Hi all, I’ve mustang 95 GT automatic transmission and I’ve found a cobra upper and lower intake, I guess from 1999 cobra (see below images). I wonder is it possible to make swap (does cobra intake fits into 95 GT automatic) - if your answer is yea what I need to buy more? If the answer is no...

Recently installed a cold air intake in my Mustang, so I’m looking to get rid of the old stock set up. The K&N filter was bought back in April, and has less than 200 miles on it. Everything is there except for the MAF sensor which I am still using on my car. $75obo. Open to trades for other SN95...

Hey all, I recently decided to replace the intake manifold gaskets as they were leaking oil onto the water pump. After I took off the manifold, I plugged the ports so I could clean the gasket surface. There are 4 ports straight down the middle, which look like they let oil go to the camshaft...

Where is the best location to install a new air intake temp sensor for my Supercharged Foxbody? In the intake or in the inlet power pipe?

I have a stock 2002 4.6 Cobra. Wondering if and intake spacer would help much at all or a larger than stock throttle body (70 or 72 or 75 or 77...) would add much...or both? Should I look toward a different than stock intake manifold? Reprogrammed chip or programmable chip or ECU? Headers...

Hi all, I need to replace the lower intake (I've learned from #stanget, its called lower intake yuhii :D ) but i wonder do i need to remove all things (waterpump, generater...)? Could you please help me? Here is a pic how long I'm come with it. If I won't bother you, I appreciate to mark what...

No idea what it is.... on a 95 GT...

In the market for a new HCI setup for my 86' fox. Currently running cobra upper and lower with a b cam making 240 to the wheels. I've searched the forums for opinions on the Anderson 6200rpm NA top end kit but only found older ones. They now include a Holley Systemax II upper and lower which is...

Does this look like a ground? 2003 mustang GT. Replaced intake and now reverse lights,speedo, and blower motor is out. Could this have something to do with it? The wire is only about 5-6 inches long and literally nowhere to plug up. Any ideas?

2 days ago I decided to go ahead and tackle my leaky intake manifold. Install was smooth, no hiccups. No more coolant leak, yes! But now I’m left with no reverse lights, no speed, odometer just shows dashes (- - - - -) <just like that, and no heat or air (only defrost). Everything on the car...

Hi together, I am new to this great place. I am from Germany and driving a 86GT and 69Mach1. Currently I am thinking about changing from the original EFI intake to an Edelbrock Performer RPM. But I am not quite sure what the result will be. My setup: - Stock cam - GT40 heads - Stock intake -...

I'm looking into 3d printing a 5.4 2v manifold for a 5.4 2v swap. The reason I am looking into this is because I would love to do a 5.4 2v swap but from what I've gathered, there are 3 problems related to the intake with that swap. You can use the 4.6 intake with adapter plates, but your fuel...

I have a factory 88 5.0 convertible and I’m installing BBK ISS. It’s a whole kit that comes with a 75mm. my question is do I have to change the MAF and 25lbs injectors.

I currently have a Fitech efi setup, but I am wanting to get rid of it and go back to a true efi system with fuel rails, etc...What do you guys recommend? Looking for something that isn't too expensive, but will be a performer. I have pulled many gt40 intakes from salvage yards so I know that is...

92 Hatch Gt mods done to motor: bigger maf with injectors to match, k&N intake, BBK fuel regulator, and MSD ignition. close to stock, never opened. I bought a tubular upper, lower intake, and the spacer off a buddy and want to know if I need heads to install it. Not sure if ports are the same...

So I am about to start modifications soon, trying to decide between the Trick Flow Track heat stage 2 kit or piece together an Edelbrock RPM2 and Edelbrock parts mimic the Trick Flow kit. What are your thoughts?

I come from fox bodies, so I'm new to the 4.6. I'm wondering if my 04 has the upgraded manifold? Under load on the freeway it gets a little bit of shaking like its motor mounts, but it seems solid at idle, any ideas what it could be? Heres some photos of my manifold. Thanks