throttle body

Hello all, I’m pretty new to the forum and this is my first post. I have a 2004 3.9 V6 and I swapped the upper intake manifold from a 4.2 onto it. I pretty clearly made a mistake, as my car now thinks it is at 18% throttle position (checked with live feed obd2 reader) when I’m completely off the...

I ran my codes the other day and got “Throttle position sensor out of range”. I have been trying to test it today and my multimeter is giving me just 0 for my reading. This is a brand new multimeter. I connected the positive to the green wire (dont have any sewing needles to pierce so I dug out...

I was upgrading my throttle body when I noticed this badge. Does it come standard?

Need some help to rectify a situation where I made a small mistake when revamping my TV Cable conenction att he throttle body. Naturally, I broke the factory connector as shown and need another. I know no aftermarket Parts Source has anything new, but, does anyone have a good lead on a used...

I have a 351W crate that is rated at 575 HP and 575 TQ. Upper intake is an Edelbrock Super Victor EFI with an Edelbrock Intake elbow. I'm not sure what fuel injector size or brand I should go with. I originally planned on 60lb injectors and getting an 80mm throttle body. I'm thinking that maybe...

I've been hunting for the most cost effective plenum option for a 2v. My major concern was that I'd like to not spend the money on an aftermarket plenum for a Pi/stock intake manifold as I will be using a Victor Jr in the future and I refuse to choke out the 4150 flange with a mmr adapter...

I have 2006 Mustang GT with a Vortech supercharger. It's pushing 460 whp and 455 tq. It was seeming off a couple weeks ago, jerking around in the lower gears like a wild bull. I then installed an air raid throttle body spacer to add a little more throttle response. I was getting a wrench light...

Hi everyone, This is my first ever post. I have a 1991 Mustang 5.0 LX. I'm looking to increase the air flow to the engine. First of all, I would like to change the original intake for a cold air intake. I will also change the original throttle body for a 70mm. That said, should I upgrade the...

Hey guys first time poster, 2003 GT owner I am getting a squeal when I just lightly tap the gas, that is the only time it squeals. No squeal when at idle. It sounds like it could be air whistling but its very high pitched and sounds like a squeak or squeal. I changed the belt and Idler pulley...

Hi, I have a 2015 salvaged coyote in a 67 mustang running on the control pack. Everything is up and running, but it seems to have a rough idle at start. The idle continues to be rough until I rev the engine and it settles down to normal at around 1000rpm for about 5 seconds, after 5 seconds...

Hey all, Been referencing stangnet forums for a while but finally joined. First forum post ever so bear with me. I have a 1989 Mustang GT 5.0 convertible that i recently got and have been upgrading here and there. Iv run into a problem and could use some help from you all. Yesterday i...

I just got a 93 cobra intake manifold (up and low) for my 90 lx vert. I wanted to upgrade the TB while I was doing the swap so I picked up a cheap used “93 cobra 65mm TB”. When I measure the opening that meets up with the intake it looks like 62mm. Is that right or did I get scammed? The price...

for sale a original GTS 60mm throttle body $75 Jonesville, VA 24263

Location: Austin, TX Price: Multiple Items Hey all! My trusty steed has been put out to pasture :-/ Therefore I'm selling my aftermarket parts (more to come!) I am will to ship (at buyer's cost) and I will accept Paypal +3% fee (unless you're willing to send the money as a gift). Steeda...

need some advice currently driving a 1994 Gt 5.0 current mods are cai, bbk shorty headers, flowmaster 40s with custom muffler delete, off road y pipes and 89 octane tune.... She's automatic sitting on 18x9 18x10.5 AMR's I'm looking to increase horsepower and add more of an aggressive sound I...

So I just bought my first car not to long ago it is a 89 mustang GT. Right away i have bin modifying it with plans of restoring and upgrading in the future. I put a 70 mm TB on and it still has the stock EGR Spacer i will be getting a 70mm spacer when i have the money. After that i started...

Get more information on the this Mustang performance throttle body here: http://www.latemodelrestoration.com/item/SVE-TB1501K/SVE-70mm-Throttle-Body-And-EGR-Spacer-50L-Mustang-86-93 Upgrade your puny factory throttle body with a SVE 70mm throttle body kit that includes the TB, correct EGR...