• Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • Classic Mustang Specific Tech

$2800 paint job now $3900

  • Thread starter Thread starter eric n
  • Start date Start date Jul 15, 2004

eric n

Founding Member
Jul 14, 2001
875
2
19
Bakersfield, CA
Jul 15, 2004
#1
  • Jul 15, 2004
  • #1
Well Yesterday the shop doing my paint called me and let me know that they had found a considerable chunk of surface rust. They suggested poping out front and rear windshields, shelby side windows, all trim pieces etc and taking the bastard down to bare metal. So..... Another 1100 and another 10 days. So the waiting goes on. DAMN, ****, DAMN, POO POO, CA CA, TI TI, DOO DOO!
 

66 BLAKE 96

Native Texican
Founding Member
Feb 16, 2001
4,810
0
0
Cowtown
Jul 15, 2004
#2
  • Jul 15, 2004
  • #2
Aww, that sucks man. You are a victim of your own thoroughness. Just tell them to knock off the big chunks of rust, and spray away.
 

302 coupe

Founding Member
Mar 2, 2000
1,952
3
36
Macon, Ga.
Jul 15, 2004
#3
  • Jul 15, 2004
  • #3
thats the way it goes dude....even though surface rust-by definition-is clearly visible as its on the surface. Its good to hear that they will be disassembling the body further, makes for an overall cleaner and longer lasting paint job. So long as you have the money, let it roll. I'd probably stop by the shop a few times during the process to make sure that they are doing all they're charging you for.
 

allcarfan

The Answer Man
Founding Member
Apr 8, 2001
2,458
1
56
North Atlanta
Jul 15, 2004
#4
  • Jul 15, 2004
  • #4
Ah, the $2800 quote was too good to be true. If they are only charging another $1100 to take the car to bare metal, body work, removed front and rear glass, thats not bad at all. They should be removing the glass and all of the trim anyway before they paint. I am assuming they are taking the whole car down to bare metal to make sure it isnt rusted in other spots? Dont be surprised if they call and raise the price again if they find more rust and have to start replacing panels and what not.
 

cardude

Founding Member
Apr 20, 2000
221
0
0
Portland, OR
Jul 15, 2004
#5
  • Jul 15, 2004
  • #5
66 BLAKE 96 said:
Just tell them to knock off the big chunks of rust, and spray away.
Click to expand...

hahaha sounds like the paint job on my stang when I purchased it.... hey what are all these bubbles????
 

zookeeper

Founding Member
Aug 25, 2001
3,415
63
109
Rogue River, Oregon
Jul 15, 2004
#6
  • Jul 15, 2004
  • #6
I can really relate to your situation. In November '02 I started to do the body part of my clone. I had spent the previous year buying all the fiberglass parts needed to build a '67 Shelby clone, so even though I'd never painted a car before and I'm painting this one, I figured I could have it done by the following summer. Since I'm doing a color change (to what color I don't know) I knew I needed to do the jambs, which meant removing the doors. The windows needed to come out anyway to redo the headliner, so out they came. To get the shelby roof scoops on, the rear seat as well as all the rear plastic and fiberglass interior panels have to come out.To really get the front of the door jambs, the front fenders need to come off. Once I got that far, I figured I may as well get the motor out and detail the engine bay. To get the engine bay right, the master cylinder, steering column, steering box and all the arms need to come out, as does all the wiring and brake lines. So gues what? now I have a bare shell of what once was a nice clean fastback in my garage. I had to buy shelves to store everything, and my wife still can't believe that it had to come this far apart "just for paint".
 

eric n

Founding Member
Jul 14, 2001
875
2
19
Bakersfield, CA
Jul 15, 2004
#7
  • Jul 15, 2004
  • #7
allcarfan,
Yeah, they're taking the whole car down to metal just to look for additional problem. Scarey what they have found under there. I've already been by the shop twice since the price increase and they are working away striping my baby naked. At the very least, it should look pretty good. I"m going to my local mustang shop today to see what new trip pieces would cost. I think it's going to scare me away. I'm already poping for new handles, marker lights, trunk "key hole" bezzel, rear turn signals..... Plus my new wheels (vintage 45's) have arrived and are now wearing khumo 712's, just waiting for a car to go on. Should be an ok (though not show quality) looking fastback.
 
R

ryanfisher1

New Member
Jul 15, 2003
7
0
0
Bakersfield, CA.
Jul 15, 2004
#8
  • Jul 15, 2004
  • #8
Eric -

I am in Bakersfield too and am getting ready to paint my 69 Mach 1, let me know where you are painting yours at.

Ryan
 

eric n

Founding Member
Jul 14, 2001
875
2
19
Bakersfield, CA
Jul 16, 2004
#9
  • Jul 16, 2004
  • #9
ryanfisher1 said:
Eric -

I am in Bakersfield too and am getting ready to paint my 69 Mach 1, let me know where you are painting yours at.

Ryan
Click to expand...

Ryan,

After I get it out of the shop and get a serious look at it, I'll clue you in. Hope it's a good review.....

welcome to stangnet, nice to have another bakersfieldian (is that a word?) onboard.
 

6Stang7

New Member
Jun 1, 2003
1,470
0
0
Livermore, CA
Jul 16, 2004
#10
  • Jul 16, 2004
  • #10
Sucks that is is gonna cost more and take longer, but it's better to pay now then to pay later when your paint starts bubbling up.
 
M

minda03GT

New Member
Apr 22, 2003
54
0
0
Richmond, Virginia
Jul 16, 2004
#11
  • Jul 16, 2004
  • #11
Body Work

I understand completely. My current project started out as a quick brake job on a beater to make it roadworthy.
About 10K later........

Anyway - I am almost done and have the car I always wanted. Take your time and don't cut any corners.
 

eric n

Founding Member
Jul 14, 2001
875
2
19
Bakersfield, CA
Aug 2, 2004
#12
  • Aug 2, 2004
  • #12
well, I'm suppose to pick up the stang today. Wearing my shelby baseball cap and everything. I went down on Friday to pick it up and let them know that they needed to square away a couple of little things before I would drive it off their property. They assured me they would be fixed this morning.

There was an additional 180 tacked onto the bill for some work they sourced out. I felt I was a bit mislead by the people I talked to about this. Could have been a misunderstanding, but I was pretty hot.

The owner/manager came up and said, "Eric, if there is anything on this bill you don't think is fair, DON'T PAY IT." We'll write it off. Whatever you think is fair is OK WITH US. Well hell! How do you stay mad at that. Gotta appreciate that attitude in a shop.

They also told me to keep it for 2 weeks, find anything that I think needs to be improved and then bring it back so that they can fix it. I'm sure there will be a fisheye or two, I did see a little overspray on one of my stripes down under the front bumper.

All in all I think I'm going to be pleased.

Just thought I'd share my excitement over getting my car back. I'll try to get some pics up soon!
 

one2gamble

Founding Member
Feb 27, 2001
902
1
0
Monterey
Aug 2, 2004
#13
  • Aug 2, 2004
  • #13
good deal, it sounds like they are treating you well. Post some pics when you get her home
 

66 BLAKE 96

Native Texican
Founding Member
Feb 16, 2001
4,810
0
0
Cowtown
Aug 2, 2004
#14
  • Aug 2, 2004
  • #14
Wow that IS hard to stay mad at. Heheh.

I can't wait to see the final product. I know it's grown to be a bit pricey, but it sounds like you are getting an amazing final product. If I took mine back because of fisheyes or overspray, my painter would LOL and blow Marlboro smoke in my face.
 

eric n

Founding Member
Jul 14, 2001
875
2
19
Bakersfield, CA
Aug 3, 2004
#15
  • Aug 3, 2004
  • #15
Picked up the car yesterday and drove it down to get my vintage 45's and kuhmo 712s put on. Love the 17 inch look. Far superior to my 15" craigars I'm going to wait a week or so before I take it in to be cut (wet sanded) and buffed. Several friends have told me it's pretty important to let the paint set up + I want to drive the bastard.

I already have a list of 13 flaws which must be fixed. Some of them are small, some of them I wonder how they missed them. I figure I'll take it in for everything at one time. Once it's tight I'll post pics.

Considering how BUSH LEAGUE the previous owners paint is and how long I drove around with that UGLY ARSE paint, I'm thrilled.
 
You must log in or register to reply here.

Similar threads

Drivetrain 83’ Glx convertible C5 Trans help!
  • JacksonJared2113
  • Dec 25, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
395
Fox 5.0 Mustang Tech Dec 26, 2025
JacksonJared2113
S
what would you do? sell the project and buy completed or finish project?
  • STANG32
  • Feb 8, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
4
Views
608
1965 - 1973 Classic Mustangs -General/Talk- Feb 16, 2025
rusty428cj
'93 Fox - On3 Turbo Build Project- PICS
  • Franomania
  • Oct 8, 2020
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 4 5 6
Replies
109
Views
17K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 5, 2023
Mustang5L5
Progress Thread Calypso Cash Pit
  • JKWilson61
  • Jun 7, 2019
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2 3
Replies
44
Views
9K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Dec 13, 2019
General karthief
Paint and Body 1962 Impala - Bodywork
  • Davedacarpainter
  • May 20, 2017
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 8 9 10
Replies
181
Views
24K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 28, 2018
02 281 GT
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • Classic Mustang Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?