• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Engine Rebuild Question

  • Thread starter Thread starter mirage86
  • Start date Start date Sep 16, 2005

mirage86

New Member
Oct 14, 2004
78
0
0
Sep 16, 2005
#1
  • Sep 16, 2005
  • #1
I'm going to rebuild a 79-81 302. The engine runs good now (stock as far as I know) in my 86 (daily driver). Compared to engine set ups that I've read on here, the following will probably be mild and boring.

I'm gonna take the block .030 over which I understand will change the displacement to a 306. Still deciding on which Pistons to get.

I'm looking at one of the Edelbrock intake and cam packages in Summit.
Performer Intake w/ Hydraulic Cam (Lift .448/.472 Dur.204/214) (Lifters included with cam).

I'm currently running an Edelbrock 650 cfm carb on the eingine.

At this point, I've got to keep the stock heads. From various books that I've got, these heads have a 67.5 - 70 cc chamber
Valve size - 1.78" Int 1.46" Exh
Port Size - 1.94" x 1.04" Int 1.24" x 1.00" Exh

With the above stated, what, if anything, should I do to the heads. Yea I know I need better ones and that is the plan for down the road. (With the wife and kids I kinda take what I can get )

Also, will the above changes make a noticable/considerable difference in torque/hp or am I just spitting in the wind? It's not for racing, it's just for me to have fun in when I'm driving it. Sorry for being so long winded.

Later
 

bluevenom867

I will have images of molesting stuffed animals in
Dec 15, 2003
1,704
1
0
St.Petersburg,FL
Sep 16, 2005
#2
  • Sep 16, 2005
  • #2
What kinda exhaust do you already got?
 
2

2002BLGT

Well-Known Member
Dec 18, 2003
2,945
4
59
Bedford VA
Sep 16, 2005
#3
  • Sep 16, 2005
  • #3
port the heads yourself before you put them on and get them milled too
 

mirage86

New Member
Oct 14, 2004
78
0
0
Sep 16, 2005
#4
  • Sep 16, 2005
  • #4
bluevenom867 said:
What kinda exhaust do you already got?
Click to expand...

Headers were on it when I got it, unk if they or stock headers or aftermarket all I know is they're not long tube lol, I installed an O/R H pipe and Flowmaster 40's dumped

Also, fwiw T-5, 8.8 w/ 4.10's
 

bluevenom867

I will have images of molesting stuffed animals in
Dec 15, 2003
1,704
1
0
St.Petersburg,FL
Sep 16, 2005
#5
  • Sep 16, 2005
  • #5
mirage86 said:
Headers were on it when I got it, unk if they or stock headers or aftermarket all I know is they're not long tube lol, I installed an O/R H pipe and Flowmaster 40's dumped

Also, fwiw T-5, 8.8 w/ 4.10's
Click to expand...

If you got a T5 with 4:10 gear I would skip the performer and go for the performer RPM.Also a little more cam wouldnt hurt.

Take advantage of thous gears.

As for the heads,you can get a hand porting kit for cheap,then have them milled for a little more compression.It will be a fun ride.

Go for it
 

mirage86

New Member
Oct 14, 2004
78
0
0
Sep 17, 2005
#6
  • Sep 17, 2005
  • #6
bluevenom867 said:
If you got a T5 with 4:10 gear I would skip the performer and go for the performer RPM.Also a little more cam wouldnt hurt.

Take advantage of thous gears.

As for the heads,you can get a hand porting kit for cheap,then have them milled for a little more compression.It will be a fun ride.

Go for it
Click to expand...


Appreciate your input

Later
 
M

macx

New Member
Jul 18, 2004
228
0
0
SE Missouri near Cape Girardeau
Sep 17, 2005
#7
  • Sep 17, 2005
  • #7
Years ago, after the Performer intakes and cams just came out, I helped a guy with a 351W full sized Bronco. We put on headers, duals, a Perf cam/kit, a Perf intake, and a 650 vac Holley. It was flat amazing what a difference it made! That combo allowed the motor to rev easily to over 5k, and it had excellent throttle response at any place in the curve. Also actually increased his gas mileage several mpg. (Course, we got rid of the smog curve in the distrib)

Unless you're going to do some major improvements on the heads, now or later, you may want to consider the Perf vs the Perf RPM pieces. With primarily stock heads, you might overmatch your heads and lose too much on low and lower mid range without gaining anything significant on the upper end where the RPM pieces shine because of the heads choking them off. If you will be able to do major improvements in your heads now or later, and like has been noted go to the lower end of the street gear range, then the RPM pieces will really wake it up, although maybe with still a little loss say below 3k or 2500 and with a little less gas mileage.

I know the RPM cam seems a little mild on duration, but also consider what rpms you usually run on the street. You can always add higher lift rockers at any time to get a little more lift and mid range torque. Just for a fun to drive street car with street gears and without killing your mileage, don't sell the Perf pieces short. You might also want to take a look at Crane & Comp cams for some street
cams with excellent torque throughout the streetable rpm range that wouldn't overmatch your heads. Might find one with just a tad more duration without going too high, but be careful of their lift, some of them go pretty high which could give you valve/piston clearance problems and start to drag down your gas mileage more than you'd want.
Nowdays, THAT can kill the fun factor in a hurry!

I purposely went with what most would consider way too mild of a cam for my 351, but I put on higher lift rockers to help the flow for torque. I'm very happy with the power and torque curve (it's a heavy car) and still gets what I consider very good gas mileage - 21.5mpg @ 80mph at 2500rpm on a 4,000lb+ car.
 

DMAN302

My mom says thanks for the pearl necklace.
Nov 8, 2003
2,120
2
59
windsor, Canada
Sep 17, 2005
#8
  • Sep 17, 2005
  • #8
If upgrading the cam I would definately want to put new springs on those heads..yours may not be up to the task due to fatigue.
 
You must log in or register to reply here.

Similar threads

Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
K
Resolved Weird sound coming from a freshly rebuilt 5.0L
  • karhoot
  • Jun 24, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
395
Fox 5.0 Mustang Tech Jun 27, 2026
Mac131
9
Engine Donor '00 Mountaineer meet '91 Fox
  • 91firecracker
  • May 11, 2026
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
41
Views
1K
Fox 5.0 Mustang Tech May 28, 2026
91firecracker
9
D
First post 289 rebuild question!
  • Ddyer2868
  • Nov 24, 2025
  • Classic Mustang Specific Tech
Replies
3
Views
361
Classic Mustang Specific Tech Dec 5, 2025
rednotch
S
5.0 Rebuild
  • smittys7up
  • Nov 29, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
14
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 16, 2026
keel
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?