Engine Rebuild Question

mirage86

New Member
Oct 14, 2004
78
0
0
I'm going to rebuild a 79-81 302. The engine runs good now (stock as far as I know) in my 86 (daily driver). Compared to engine set ups that I've read on here, the following will probably be mild and boring.

I'm gonna take the block .030 over which I understand will change the displacement to a 306. Still deciding on which Pistons to get.

I'm looking at one of the Edelbrock intake and cam packages in Summit.
Performer Intake w/ Hydraulic Cam (Lift .448/.472 Dur.204/214) (Lifters included with cam).

I'm currently running an Edelbrock 650 cfm carb on the eingine.

At this point, I've got to keep the stock heads. From various books that I've got, these heads have a 67.5 - 70 cc chamber
Valve size - 1.78" Int 1.46" Exh
Port Size - 1.94" x 1.04" Int 1.24" x 1.00" Exh

With the above stated, what, if anything, should I do to the heads. Yea I know I need better ones and that is the plan for down the road. (With the wife and kids I kinda take what I can get :rlaugh: )

Also, will the above changes make a noticable/considerable difference in torque/hp or am I just spitting in the wind? It's not for racing, it's just for me to have fun in when I'm driving it. Sorry for being so long winded.

Later :nice:
 
bluevenom867 said:
What kinda exhaust do you already got?

Headers were on it when I got it, unk if they or stock headers or aftermarket all I know is they're not long tube lol, I installed an O/R H pipe and Flowmaster 40's dumped

Also, fwiw T-5, 8.8 w/ 4.10's
 
mirage86 said:
Headers were on it when I got it, unk if they or stock headers or aftermarket all I know is they're not long tube lol, I installed an O/R H pipe and Flowmaster 40's dumped

Also, fwiw T-5, 8.8 w/ 4.10's

If you got a T5 with 4:10 gear I would skip the performer and go for the performer RPM.Also a little more cam wouldnt hurt.

Take advantage of thous gears.

As for the heads,you can get a hand porting kit for cheap,then have them milled for a little more compression.It will be a fun ride.

Go for it :nice:
 
bluevenom867 said:
If you got a T5 with 4:10 gear I would skip the performer and go for the performer RPM.Also a little more cam wouldnt hurt.

Take advantage of thous gears.

As for the heads,you can get a hand porting kit for cheap,then have them milled for a little more compression.It will be a fun ride.

Go for it :nice:


Appreciate your input

Later
 
Years ago, after the Performer intakes and cams just came out, I helped a guy with a 351W full sized Bronco. We put on headers, duals, a Perf cam/kit, a Perf intake, and a 650 vac Holley. It was flat amazing what a difference it made! That combo allowed the motor to rev easily to over 5k, and it had excellent throttle response at any place in the curve. Also actually increased his gas mileage several mpg. (Course, we got rid of the smog curve in the distrib)

Unless you're going to do some major improvements on the heads, now or later, you may want to consider the Perf vs the Perf RPM pieces. With primarily stock heads, you might overmatch your heads and lose too much on low and lower mid range without gaining anything significant on the upper end where the RPM pieces shine because of the heads choking them off. If you will be able to do major improvements in your heads now or later, and like has been noted go to the lower end of the street gear range, then the RPM pieces will really wake it up, although maybe with still a little loss say below 3k or 2500 and with a little less gas mileage.

I know the RPM cam seems a little mild on duration, but also consider what rpms you usually run on the street. You can always add higher lift rockers at any time to get a little more lift and mid range torque. Just for a fun to drive street car with street gears and without killing your mileage, don't sell the Perf pieces short. You might also want to take a look at Crane & Comp cams for some street
cams with excellent torque throughout the streetable rpm range that wouldn't overmatch your heads. Might find one with just a tad more duration without going too high, but be careful of their lift, some of them go pretty high which could give you valve/piston clearance problems and start to drag down your gas mileage more than you'd want.
Nowdays, THAT can kill the fun factor in a hurry!

I purposely went with what most would consider way too mild of a cam for my 351, but I put on higher lift rockers to help the flow for torque. I'm very happy with the power and torque curve (it's a heavy car) and still gets what I consider very good gas mileage - 21.5mpg @ 80mph at 2500rpm on a 4,000lb+ car.