First start up using megasquirt.. 1992 5.0.

Blucifer99 · Apr 30, 2019

just to the right alittle bit

a91what · Apr 30, 2019

Your TFI is not firing like it's supposed to When you remove the spout the computer no longer has control of the timing it is supposed to revert to 10ﾟ base Since that's not happening we have to do it this way

a91what · Apr 30, 2019

Based on that picture adjust the distributor tell its center and then use the trigger wizard to set the timing

Blucifer99 · Apr 30, 2019

nvm i had to spin it again i missed my markl

Blucifer99 · Apr 30, 2019

i missed my mark went to 23 instead of 25 but this is 25... so i center that rotor on the #1 by turning the dizzy.. then set timing the usual way using megasquirt trigger wizard

a91what · Apr 30, 2019

Yes, once its centered you will not touch the distributor again.

Blucifer99 · Apr 30, 2019

a91what said:
Yes, once its centered you will not touch the distributor again.

ok well its centered to the best of center that my eyeballs can get.. well lets see what happens now

a91what · Apr 30, 2019

One more thing to mention, ideally the trigger offset will be 0-10*

Blucifer99 · Apr 30, 2019

a91what said:
One more thing to mention, ideally the trigger offset will be 0-10*

well mine landed on 13.50 and thats 20degrees.. i hammered out autotune for 3 blocks on easy cause it was super lean.. then normal for a few blocks didnt go far.. up the road and back

Blucifer99 · Apr 30, 2019

well i hope i didnt just mess something up driving it cause i didnt see that last message.... i got the rotor centered on #1 then set my timing to 20 using fixed timing.. and now that i think of it... i didnt pull the spout.. ughh great..

Blucifer99 · Apr 30, 2019

well i guess im gonna go out and pull the spout and see if it shuts off or not... god dammit. i tell ya ill never do this again.

a91what · Apr 30, 2019

You wont pull the spout, 13.5 is fine. That's just the lowest timing advance you can run is all.

Blucifer99 · Apr 30, 2019

you realize that i meant 13.50 in trigger wizard meant 20 degrees on fixed timing right?? not its set at 13.50 base timing. lol i just caught that

a91what · Apr 30, 2019

Yes the 13.5 is the offset.

Blucifer99 · Apr 30, 2019

a91what said:
Yes the 13.5 is the offset.

and i was lookin over my datalog from the drive.. so according to my initial values table " it think that what controls my idle valve when hot in closed loop" thats the table my idle valves supose to follow right.. cause i noticed my valve is only open to about 13.4-19 ish.. and i have it set to be open about 30ish... so from what happend before with my car when i had the throttle body screw out to much.. should i sync my table up to my throttle body screw again..

a91what · Apr 30, 2019

No, that table is used as a simple lookup table for when you go into closed loop, it is meant to give the idle valve a starting point. The goal is to get the valve into a position over what is needed then it will smoothly transition into cl idle.

Blucifer99 · Apr 30, 2019

a91what said:
No, that table is used as a simple lookup table for when you go into closed loop, it is meant to give the idle valve a starting point. The goal is to get the valve into a position over what is needed then it will smoothly transition into cl idle.

ahh ok well then what would be causing my idle valve to be closing while at idle... before it held at around 20.1 but it was lower until i adjusted my tb . and i figured its the same idea now... cause i havnt really touched that screw yet.. except for a 1/2 turn when starting the car. k well i guess i gotta look over my tune and see where abouts my idle valve should be sitting at idle.

Blucifer99 · Apr 30, 2019

and i guess trickflow stage one cams pull crap for vaccuum.. i was kinda hoping for abit lower MAP. been searchin the net to see if theres any info on that cam and the amount of vac it pulls. but i guess with a lobe sep of 110. it wouldnt pull high vac.

Blucifer99 · May 1, 2019

whats the range between offsets thats allowable>?. after i got my car hot i had to readjust the offset to get the timing to match trigger wizard.. had to bump it up to 15ish from 13.50.. isnt there a range in offset that works best?
after i did that 25degree check where the rotor was pointing thing. it seems i may have went alittle to far.

a91what · May 1, 2019

0-19* is allowed.

First start up using megasquirt.. 1992 5.0.

I only understand every 3rd word

Attachments

SendMeUrDataLog

SendMeUrDataLog

I only understand every 3rd word

I only understand every 3rd word

Attachments

SendMeUrDataLog

I only understand every 3rd word

SendMeUrDataLog

I only understand every 3rd word

Attachments

I only understand every 3rd word

I only understand every 3rd word

SendMeUrDataLog

I only understand every 3rd word

SendMeUrDataLog

I only understand every 3rd word

SendMeUrDataLog

I only understand every 3rd word

I only understand every 3rd word

I only understand every 3rd word

SendMeUrDataLog

Similar threads

Privacy & Transparency

Privacy & Transparency