How To Remove Blower Belt?

FastSVO · Jun 19, 2016

Hi folks I have a Vortech s trim on a 1991 Fox body and I have never removed the blower belt before. Would like to know what's the best approach and any tips of possible. Also, what do I have to do to get the correct tension when I replace the belt?

Thanks in advance!

Sent from my SM-N920P using Tapatalk

mikestang63 · Jun 19, 2016

loosen the adjusting bolt on the vortech tensioner bracket. That is also how you achieve the proper tension.- you will see a hole to stick a rachet handle in,, Anderson motorsports sells a nice adjuster that you can simply tghten down on a bolt. Here is a picture of the tensioner bracket with the bolt to loosen to remove the belt, the hole for the ratchet and the anderson part.

JD1964 · Jun 19, 2016

mikestang63 said:
loosen the adjusting bolt on the vortech tensioner bracket. That is also how you achieve the proper tension.- you will see a hole to stick a rachet handle in,, Anderson motorsports sells a nice adjuster that you can simply tghten down on a bolt. Here is a picture of the tensioner bracket with the bolt to loosen to remove the belt, the hole for the ratchet and the anderson part.

Interesting. Mike, I dont have that bolt style tensioner on my S trim setup. Just the flat brackets where I pry and tighten bolts to hold it in place. It's a narrow fit so I had to sacrifice a wrench to the grinder and make it narrower to fit in there.

mikestang63 · Jun 19, 2016

John Dirks Jr said:
Interesting. Mike, I dont have that bolt style tensioner on my S trim setup. Just the flat brackets where I pry and tighten bolts to hold it in place. It's a narrow fit so I had to sacrifice a wrench to the grinder and make it narrower to fit in there.

that is the anderson part

FastSVO · Jun 19, 2016

John Dirks Jr said:
Interesting. Mike, I dont have that bolt style tensioner on my S trim setup. Just the flat brackets where I pry and tighten bolts to hold it in place. It's a narrow fit so I had to sacrifice a wrench to the grinder and make it narrower to fit in there.

Yes, same here. My brackets do not have the holes for the rachet.

Sent from my SM-N920P using Tapatalk

JD1964 · Jun 19, 2016

FastSVO said:
Yes, same here. My brackets do not have the holes for the rachet.

Sent from my SM-N920P using Tapatalk

I have the square hole for the ratchet, just not that bolt tensioner that mike showed in the pic.

JD1964 · Jun 19, 2016

Mike, you got the 8 rib setup? Mine is the 6.

FastSVO · Jun 20, 2016

John Dirks Jr said:
I have the square hole for the ratchet, just not that bolt tensioner that mike showed in the pic.

My bad. I just checked my car and the bracket plate is indeed the same with the key hole for the rachet.

Sent from my SM-N920P using Tapatalk

FastSVO · Jun 20, 2016

How many ft lbs do you torque the bolt down after reaching the tension you want? Regarding the tension, how do you know if you are in the "green" zone?

Sent from my SM-N920P using Tapatalk

How To Remove Blower Belt?

FastSVO

mikestang63

JD1964

there is enough sticking out to grab on to

mikestang63

FastSVO

JD1964

there is enough sticking out to grab on to

JD1964

there is enough sticking out to grab on to

FastSVO

FastSVO

Similar threads

How To Remove Blower Belt?

there is enough sticking out to grab on to

there is enough sticking out to grab on to

there is enough sticking out to grab on to

Similar threads

Privacy & Transparency

Privacy & Transparency