Progress Thread 74 Mustang II - Build as semi-daily driver

[Noobz347]

If that air damn can take curb, then I like it.


Probably the fastest mustang two in the world for this week.
Score an extra point.
Our Hero extra_stout!

It sits under the radiator support on my 86 so.... Don't park on the sidewalk.

 

[extra_stout]

Cut, shape, and fit something like this to the front of the car to help cut air beneath the car:

You know... I like to experiment, but I also like to be alive.

 

[Noobz347]

You know... I like to experiment, but I also like to be alive.

Ok... How does that apply?

 

[General karthief]

Ok... How does that apply?

Something about parking on the sidewalk?

 

[extra_stout]

On the 1gen Mustang race car drivers had problem with aerodynamics beginning at 140 MPH... in a way that the hood did act like a wing and the car did get light at the front wheels. I don't want to experience that.

I do not want to experiment with aerodynamics... or with parking on sidewalks.

 

[extra_stout]

My tacho conversion seems to work. A friend helped me with RPM reading with my ignition light and comparing it to the modified tacho... at night, because it is much easier at daylight.
I will post some pictures how I did the conversion. Its not more than 100 RPM off from idle up to 4000 RPM. That works for me.
- burn the whole fuel tank nearly empty to get new fuel into it before wheater is getting bad
- tacho conversion from 6 to 8 cylinders => 650 Ohm resistor
- installation of new used fuel level and water temp gauge (the old ones get stuck, the new used ones worked fine in a bench test)
- reverse light is not working; look up where the error is
- maintanance

Things I want to do, but will more likely a thing for next year (hopefully):
- remove DB killers from exhaust (measure before and after to see if it is nearly legal)
- install new u-joints on driveshaft (+ paint); check drive line angles
- custom adjustable front sway bar
- wheels?!

I just passed TÜV inspection without problems
So two years more driving with inner pease. I tought it could be time to cross of old points from my todo list and add new points:
- burn the whole fuel tank nearly empty to get new fuel into it before wheater is getting bad
- tacho conversion from 6 to 8 cylinders => 650 Ohm resistor
- installation of new used fuel level and water temp gauge (the old ones get stuck, the new used ones worked fine in a bench test)
- reverse light is not working; look up where the error is
- maintanance

- remove DB killers from exhaust (measure before and after to see if it is nearly legal)
- install new u-joints on driveshaft (+ paint);
- wheels?! update 2026: at home and modified to fit the car; need to get tires
- check drive line angles and check driveshaft slip yoke for play
- front springs installation
- rear spoiler installation / repaint hood scoop and rear spoiler in 2K epoxy paint (black)
- check wiring of lamda sensor
- install gauges (solution for oil temp and pressure sensor?!)
- custom adjustable front sway bar

Hopefully I have more time for the car in the next two years. Drove just little more than 1000 miles in the last two years...

 

[Bullitt347]

I do not want to experiment with aerodynamics... or with parking on sidewalks.

A front air dam is hardly "experimenting"
Virtually ever car/truck ever made in the last 40+ years has a front air dam on it.
It is a proven way to keep air from getting under the vehicle, which helps stability and improves fuel efficiency.

 

[2Blue2]

Drove just little more than 1000 miles in the last two years...

Right on Extra Stout
I luv this update!

Seeing things checked off list is Good!
Passing Inspection = Most excellent
Still putting milage on that old Mustang feels nice.
Still might need a fresh picture...

 

[greenflash79]

"- tacho conversion from 6 to 8 cylinders => 650 Ohm resistor"

Where did you install this resistor?

The speedometer and tachometer have different readings on the V8; did you change both of them?

 

[LILCBRA]

Our speedometers are mechanically driven so there should be no need to install a resistor for it.

 

[extra_stout]

The resistor converted the V6 RPM gauge to work with the V8 ignition signal input.
The C4 speedometer cable worked fine with the T5 transmission, I just needed to to the math to chose the right tooth count for the speedometer gear.

@2Blue2 you will get fresh pictured at latest when I get new wheels installed...

 

[welder4956]

"- tacho conversion from 6 to 8 cylinders => 650 Ohm resistor"

Where did you install this resistor?

Looks like the resistor goes in the red wire: https://stangnet.com/mustang-forums/threads/tachometer-conversion-from-6-to-8-cylinder-will-also-work-for-4-to-6-or-4-to-8-but-with-different-resistor-size.924607/#:~:text=The conversion works only from lower cylinder,shows with a V8 following RPM: RPMv6tacho=8/6*RPMreal.