Progress Thread Barn Find - Twilight Blue 1991 GT 5spd

idareu · Jun 14, 2022

General karthief said:
I would agree with Stanglx or possibly call that mustang salvage yard in Georgia and ask if they can cut a piece out of a wreck, there is very little structural integrity there, it could be cut out and another butt welded fairly cheap.
I'll forget about that $15 bucks you owe me for the zip ties, ratchet straps and wood you used since the car had hidden damage.

I tried the floor jack and block of wood but the lower support is bent upwards and towards the front of the car. It was worth a shot so thanks to you and Stanglx for the suggestion. I'll start looking around for a support locally. There used to be some pretty decent salvage yards over by Orlando Speedway. If that doesn't pan out, I'll take a look at that one is Georgia (I think it was MPS salvage) and karthief , I'm sure you will make up that $15 when I start pestering you for parts.

Mustang5L5 · Jun 14, 2022

You should try a spot cleaner on those seats before giving up on them. Might take out all those stains.

Potomus Pete · Jun 14, 2022

Soak em down good with carpet cleaner, and suck it up with a shopvac...Or go to rent a carpet cleaner that has a hose. Works great

LX1993 · Jun 14, 2022

Agreed. Carpet cleaner with hot water. Then windex, (best thing I've used on upholstery, leaves no residue). That, a 25# box of rags, 12 pack (in my case 30) & an afternoon. Keep scrubbing until they come clean. As far as the core support, do yourself a favor & buy a mig welder. You will use it more than you think. Skip the flux core stuff. You can get a mig on Amazon for $150. Grab an 80 cu. ft. bottle of C-25 & .023-.035 wire. Some scrap steel & another afternoon, I think you'd be surprised at your progress. Like was said, pretty much not a structural part. I will say I'd look for a used Hobart or Lincoln 140. Those older transformer type welders have better arc stability at the high & low limits of the machine than the newer inverter boxes.

idareu · Jun 16, 2022

Thanks everyone for the suggestions on the upholstery although I've never heard of using Windex on it, what the hell it can't hurt to try. I plan on pulling everything out this weekend and will give them a good scrubbing. I figure I can do that and move the engine off the hoist onto the engine stand this weekend and it will be a good weekend. I need to give the engine a once over and make sure things are buttoned up tight. The upper intake manifold is off and I need to tighten up the oil pan but other than that, it looks really good.

I'm looking at MIG welders now. I figure if I can find one for a decent price, I'll give it a shot. I definitely will get some scrap steel to practice on before I even think about doing it on the car. I'm totally green on this so it will be an experience that's for sure.

General karthief · Jun 16, 2022

That lower piece is a good place to hone your skills, if you choose to cut the spot welds all you do is plug weld the new piece in. You don't have to worry about any alignment issues.

limp · Jun 16, 2022

I have watched some detailers use a steam cleaner for upholstery do some amazing things with some interiors.....

Noobz347 · Jun 16, 2022

General karthief said:
I'll forget about that $15 bucks you owe me for the zip ties, ratchet straps and wood you used since the car had hidden damage.

Don't let him lowball you on that Hatch Prop 9000. Those things are rare.

idareu · Jun 16, 2022

Noobz347 said:
Don't let him lowball you on that Hatch Prop 9000. Those things are rare.

Haha, Yeah it's a limited edition. I think there's a certificate of authenticity somewhere in the glove box. But..... It was "IN" the car when I paid for it sooo, possession is 9/10 of the law.

He did hook me me up with a couple of ratchet straps/pieces of wood to help hold the engine in place in the bed of the truck. All I had was 2" thick straps for securing the car to the trailer. The zip-ties were used to bind the excess straps once she was on the trailer. I told him I'm sure I'll make it up to him once I get my laundry list of parts together. I foresee a few more trips to Polk county in my future.

General karthief · Jun 16, 2022

The truth is he used 67 large black zip ties to hold the back of the car to the trailer, I found those cheap azz ratchet straps on the bed of the dump truck.

General karthief · Jun 16, 2022

Keep this link

https://stangnet.com/mustang-forums/threads/door-panel-tops.922389/

idareu · Jun 16, 2022

General karthief said:
Keep this link

https://stangnet.com/mustang-forums/threads/door-panel-tops.922389/

Good stuff, I was actually reading that one this afternoon.

idareu · Jun 18, 2022

I spent a good part of the afternoon in the garage but damn this FL heat can wipe you out. I did get the hatch support struts installed so no more custom broomstick support now. I also started disassembling the interior. My plan is to take everything out and either repair, repaint or replace the pieces. I'm ordering the duel cup holder center console and arm rest from LMR to replace mine with the broken ashtray. I got the seats out and will spend some time cleaning them tomorrow. I had hope that I could get away with a good cleaning of the carpet but so much for that, a previous owner cut out the carpet in the passenger foot well for some reason. No worries thought, I had budgeted for new carpet anyway.

Seats are out. Got to love the things you find when you start pulling stuff out like this. I found 2 cassette tapes (Spanish music), a couple of screwdrivers, channel locks, kid toy parts in the back, and an assortment of loose change.

So much for cleaning and re-using the carpet.

Now out to a few questions, First there is pitting on the trim pieces all around the exterior. Can this be sanded down and smoothed out or am I better off looking for new trim/ground effects.

Second question, Does anyone know of an online source for a new dash.? Mine is cracked in several places. I will be heading to a few salvage yards later next week but figured it was worth asking if anyone knew of a reproduction one.

LX1993 · Jun 19, 2022

No one repop's the dash yet. Ebay, face book or salvage yard. Easier to just replace the exterior trim. It's all available & reasonable.

TIGGER · Jun 19, 2022

My 89 has the same pitting trim where the paint has flaked off. I am going to try and refinish the original pieces on my car. Some are in better shape than others. I picked up some Evercoat polyester flexible glazing putty to fill in the rough spots but I have not tried it yet.

idareu · Jun 19, 2022

Thanks @LX1993 and @TIGGER for the replies. As far as the dashboard goes, it's off to the salvage yard for starters (unless karthief has one hidden in his pile-o-parts LOL ). I may try to play with the trim pieces and see if I can clean them up but if not, I'll get new ones. Paint./Body work is a long way off for now. Right now the plan is to to get it running first so I can move it in and out the garage under its own power.

Middleagecrisis · Jun 27, 2022

LX1993 said:
No one repop's the dash yet. Ebay, face book or salvage yard. Easier to just replace the exterior trim. It's all available & reasonable.

Hmmm, I found these: https://lmr.com/products/79-93-Mustang-Dash-Pads I'd look on CJ's Pony, as well.

Mustang5L5 · Jun 27, 2022

You can get parts for the dash, but not the entire thing just yet. You still need the core frame material of the dash used. You can clean it up, scuff it up and paint it.

From there you can track down the HVAC registers, the speaker grills and the dash pad.

I've found SEM Landeau black to be a very good color for restoring the black trim pieces in the interior

Mstng93SSP · Jun 27, 2022

Make sure if you find a dash it is from a 90-93. 87-89 are different.

91TwighlightGT · Jun 27, 2022

LX1993 said:
No one repop's the dash yet. Ebay, face book or salvage yard. Easier to just replace the exterior trim. It's all available & reasonable.

This is going to depend a little bit. I don't know what the quality of the reproduction pieces are, but used it's a bit of a crap shoot on whether or not you will get something in decent shape. Those bumper extensions and the GT ground effects in general have often been ravaged by weather and time as far as used pieces are concerned.

Looking further at the pictures, the damage is also on the bumper cover itself, so that part would need to be repaired or the bumper cover replaced. The last time I bought a YCC reproduction for my Mustang project was 10 years ago, so I don't know what the cost (or availability) of those are anymore. The ones from LMR were pricey and again availability of a lot of these things are questionable as well as the quality.

To the OP - I think those are absolutely repairable. I probably would put some plastic filler in and THEN sand it down or you may take off too much material and change the shape too much.

Progress Thread Barn Find - Twilight Blue 1991 GT 5spd

idareu

Mustang5L5

That is…until I whipped out my Bissell

Potomus Pete

I'm still waiting for the fully nude shots

LX1993

idareu

General karthief

wonder how much it would cost to ship you a pair

limp

wrap a little cheese around it and its a done

Noobz347

Stangnet Facilities Maint Tech... Er... Janitor

idareu

General karthief

wonder how much it would cost to ship you a pair

General karthief

wonder how much it would cost to ship you a pair

idareu

idareu

LX1993

TIGGER

idareu

Middleagecrisis

Active Member

Mustang5L5

That is…until I whipped out my Bissell

Mstng93SSP

You have a nice rear end there Dave.

91TwighlightGT

Similar threads

Progress Thread Barn Find - Twilight Blue 1991 GT 5spd

That is…until I whipped out my Bissell

I'm still waiting for the fully nude shots

wonder how much it would cost to ship you a pair

wrap a little cheese around it and its a done

Stangnet Facilities Maint Tech... Er... Janitor

wonder how much it would cost to ship you a pair

wonder how much it would cost to ship you a pair

Active Member

That is…until I whipped out my Bissell

You have a nice rear end there Dave.

Similar threads

Privacy & Transparency

Privacy & Transparency