I mean you read your CT and then then this and its kinda funny..."small increments in length make a big difference"
Progress Thread No Clear 92 (Lack of) Progress thread
- Thread starter DadLife0724
- Start date
Me and the boy took the mustang to watch the races Friday night. On a hard pull I kinda felt a loss of power. Noticed I developed a helluva whistle. Gonna get a smoke tester. I see some on Amazon, but I don't wanna waste money on junk. Anyone have experience with Amazonian smoke testers?
gkomo
now i can hopefully expect to receive the shaft
I haven't used mine yet, but i did do a fair amount of research when purchasing it and ended up with a Solary brand machine. It got great reviews and was fairly cheap.
Look for one with a pressure regulator. That way you can set it to a given amount , 1 or 2 psi and it wont blow out any seals. I believe mine was about 80-90 bucks. Works real good.
Didn't want to wait on a smoke tester. I do still plan on purchasing one, but for for now I used a hand transfer pump from hobo freight and a cigar. Found zero leaks in the vacuum system.
I have gone over the car multiple times with it idling. Whistling seems to be coming from 70mm SR Performance TB. Makes sense I guess. Noticed it was hanging open just a bit too. Cleaned it up and got it to close fully. Still have the whistle. But throttle doesn't hang up anymore and I seemed to have gotten my power back.
1/2" smaller belt should be here today, hopefully that will fix my belt shavings issue and put my tensioner back into range.
I have gone over the car multiple times with it idling. Whistling seems to be coming from 70mm SR Performance TB. Makes sense I guess. Noticed it was hanging open just a bit too. Cleaned it up and got it to close fully. Still have the whistle. But throttle doesn't hang up anymore and I seemed to have gotten my power back.
1/2" smaller belt should be here today, hopefully that will fix my belt shavings issue and put my tensioner back into range.
Smaller belt is on. Kinda put the tensioner back in range. It was a bear to get on. Don't think I could go any smaller than that. Could this tensioner just be on the outs? Looks to be an OG Ford part.
TB is hanging open a tiny bit again. Idles a little high and whistles while stopped. Not every time, but here and there. I can push it closed with my finger and it idles normal and stops whistling. Next step may be to remove it and clean it up. It shouldn't be that dirty. It has less than 500 miles on it.
TB is hanging open a tiny bit again. Idles a little high and whistles while stopped. Not every time, but here and there. I can push it closed with my finger and it idles normal and stops whistling. Next step may be to remove it and clean it up. It shouldn't be that dirty. It has less than 500 miles on it.
Attachments
gkomo
now i can hopefully expect to receive the shaft
Interesting you can push it closed. Is there a spring that holds it closed thats just not doing its job properly?
Yes. There is some slack in the spring. I am going to take a closer look tomorrow when I pull it off.
Tensioner may be shot. I ended up getting one from the parts store that someone returned all hacked up but the second one from RockAuto worked great
I did replace the pulley it came with with a steel one.
Post in thread 'Serpentine belt squeal after reinstall?'
https://stangnet.com/mustang-forums...lt-squeal-after-reinstall.928788/post-9422194
I did replace the pulley it came with with a steel one.
Post in thread 'Serpentine belt squeal after reinstall?'
https://stangnet.com/mustang-forums...lt-squeal-after-reinstall.928788/post-9422194
Last edited:
I will take a look around. I got one from a local parts store at one point to compare to my current and it looked and felt like 
right out the box. I returned it and stuck with mine. Seems time to look elsewhere.
right out the box. I returned it and stuck with mine. Seems time to look elsewhere.
Well this is wonderful. Second plenum this summer. Torque is always set to 18 ft/lbs.
I am starting to think torque spec might be lower with the spacer in between upper and lower. Any input on that would be greatly appreciated.
I am starting to think torque spec might be lower with the spacer in between upper and lower. Any input on that would be greatly appreciated.
Remove the spacer, I hate those damn things unless its a billet nitrous plate. I never torque the uppers, just hand tight with a 1/4" ratchet or one of those palm gimble ratchets if it's got some pita to reach bolts.. Never cracked one. As for the belt its the aftermarket ps bracket, its was designed to be use with the tension rod alt mount when march came out with them, not the stock one/ stock tensioner. It doesnt raise the pump location like the frpp a/c delete kit does.
